Land Rover Discovery 1 Parts

Cylinder Head Gasket of composite construction for the 3.5L V8 petrol engine. The gasket seals the joint between the cylinder head and the block, ...

Bolt. Hexagon-head threaded fastener for general assembly and retaining applications. Supplied individually.

Rear Wheel Arch is the inner body panel that forms the arch over the rear wheel, part of the rear body assembly. This is the two-door version, whi...

Rear Wheel Arch is the inner body panel that forms the arch over the rear wheel, part of the rear body assembly. This is the two-door version, whi...

Pipe Adaptor is a double-male union fitting in the automatic transmission oil cooler circuit. It joins two pipe runs, carrying transmission fluid ...

Selector Fork is the 1st/2nd gear selector fork for the 5-speed manual gearbox. It engages the 1st/2nd synchroniser sleeve, moving it along the ma...

Water Pump

Reverse Idler Gear Assembly for the LT77 five-speed manual gearbox. Provides the reverse gear train, reversing mainshaft rotation for reverse driv...

Shift Plate

Top Link Bracket for the rear suspension, right-hand side. This chassis-mounted bracket provides the upper pivot point for the rear suspension lin...

Wheel Bearing Kit - Front and Rear

Four-Stage Adjustable Shock Absorber for the suspension damping circuit, mounted between the axle and the chassis mounting point. The damper contr...

Kit diff wh OEM NLA AFTER STOCK ENDS

Oil Seal

Exhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...

Connecting Rod Bolt for the Rover 3.5L V8 petrol engine. The bolt clamps the connecting rod big-end cap to the rod, retaining the big-end bearing s...

Coolant Adaptor (Reducer) - threaded adaptor in the engine oil cooler circuit at the radiator. This threaded reducer adaptor connects the engine o...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Oil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...

Complete Cylinder Head for the 300 TDi 2.5L diesel engine, supplied fully assembled and ready to fit. The head is delivered built up with the valv...

bush shock absorber OEM, bush anti roll bar OEM

Cable Clip for securing and routing cables and wiring to body and chassis structures.

The Maxtrac Blindo 16x7 alloy wheel is designed for off-road durability and rugged performance, making it the perfect choice for Land Rover and 4x4...

Shock Absorber for the front suspension — the hydraulic damper that controls spring movement at the front axle. The damper resists and slows the c...

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Brake Master Cylinder - ABS is the tandem master cylinder at the head of the hydraulic braking circuit, specified for the servo-assisted anti-lock ...

Main bearing kit 0.020" undersize OEM AE

Power steering pipe forming the low-pressure return leg of the power steering hydraulic circuit, running from the steering box return port back to ...

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Heater Hose - Inlet & Outlet is a moulded coolant hose assembly in the heater circuit of the engine cooling system, carrying the combined feed ...

Crankshaft Position Sensor for 4-cylinder petrol applications - 1.8L K Series and 2.0L MPi T Series - mounted at the crankshaft in the engine block...

Bearing transfer box LT230 intermediate shaft

Power Steering Pump - V8

Light Guard Set - protective guards for the rear lamp units, mounted on the rear wings. The guards fit over the rear lamp lenses and shield them a...

Rear Door Lock Assembly - LH - complete latch and lock mechanism for the left-hand rear door, operating within the door locks and handles assembly ...

Alloy Wheel, 18 x 8 with ET20 offset and a 5 x 165.1 mm (five-stud) bolt pattern, finished in black. The wheel forms the mounting interface betwee...

Differential Pinion Flange Kit for the three-bolt drive flange on the axle differential. The pinion flange mounts on the differential pinion shaft...

Spring Dislocation Cones - Front are fitted inside the front coil springs to prevent spring dislocation under maximum suspension droop. During extr...

Mainshaft for the LT77 five-speed manual gearbox, Suffix H specification. The mainshaft is the gearbox output shaft. It carries the synchroniser h...

Valance Panel - a replacement body panel forming part of the outer bodywork in the wheelarch and valance area of the lower body.

Rear Gas Shock Absorber - a gas-charged hydraulic damper for the rear suspension, controlling axle movement over road and off-road terrain. Matche...

Front Coil Springs - heavy-duty road springs for the front axle, supplied as a pair. The springs seat between the front axle and the chassis sprin...

Fuel Pipe Assembly - part of the fuel delivery circuit for the carburettor V8. It carries fuel from the fuel supply line to the SU carburettors, fe...

O-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.

Intercooler Hose the upper charge-air hose in the intercooler circuit of the 200TDi diesel engine. It carries cooled, pressurised charge air from ...

Radiator Area Retention Clip used in the cooling system assembly. This clip secures cooling system components - including fan cowl panels and radi...

Fuel Tank Inspection Plate Seal is a rubber sealing gasket for the fuel tank inspection plate in the fuel tank assembly. The inspection plate prov...

Propshaft Nut - Rear - nut retaining the rear propshaft flange at the rear differential pinion. The nut clamps the propshaft coupling flange again...