Land Rover Discovery 1 Parts

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Electronic Differential Lock (E-Locker) replaces the standard open differential assembly within the axle, providing driver-selectable full differen...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Headlamp Levelling Motor for the front headlamp assembly. Electric actuator that adjusts the headlamp beam angle to compensate for vehicle load. M...

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Tow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Autogear Power Syn 75W90 5L

Rear Coil Springs - Medium Load, +2" Lift (Terrafirma), supplied as a pair. This is a LIFT spring: it raises the rear by approximately 2" (50mm) o...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Thrust Washer 1.45mm Diff - LT230

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Gasket

Cam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...

Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...

Crankshaft Main Bearing Cap Cross-Bolt Seal Washer for the Rover V8 petrol engine. This 19mm diameter seal washer seals the main bearing cap cross...

Layshaft Nut for the R380 five-speed manual gearbox. It secures the layshaft gear cluster on its shaft, torqued to specification and then staked in...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Towing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Body Mount - To Chassis Frame is a rubber isolation mount positioned at one of the body-to-chassis attachment points. The mount cushions the body ...

Flanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...

Oil pump relief valve washer V8

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Mainshaft for the R380 5-speed manual gearbox. The mainshaft is the central driven shaft within the R380 gearbox, carrying the output gear cluster...

Rear Coil Spring - Heavy Duty, +2" Lift A rear suspension coil spring from the Terrafirma range, seating between the axle and the chassis spring s...

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Bellhousing Gasket for the ZF automatic transmission, sealing the joint between the engine rear face and the transmission bellhousing. It maintain...

Pipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...

spring synchro FTC4992

Flange Nut - M10 Nyloc is an M10 x 1.5 nylon-insert flange nut used on the exhaust system, securing the joints between the turbocharger or manifold...

Rear Propshaft Rubber Coupling - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while ab...

Coil spring trim spacers, 5 mm, fitted between the lower spring mounting plate and the axle to make fine ride height adjustments. Spacers are stac...

H4 Spare Bulb and Fuse Kit for 12V vehicles with H4 headlamps, holding replacement bulbs for the main exterior lamps and spare blade fuses in a com...