Land Rover Discovery 1 Parts

Stub Axle Kit - front stub axle with its sealing and fixing parts for one corner. The stub axle bolts to the outer face of the swivel housing and f...

Turret Securing Ring for the front shock absorber turret, supplied as a pair. The rings clamp the turret to its mounting in the front suspension. ...

Front Shock Absorber fits in the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface....

Alternator upgrade kit for the 200Tdi 2.5L 4-cylinder turbo diesel, replacing the standard alternator in the engine charging circuit with a higher-...

Stub Axle Kit - Rear Discovery 1 RRC

200 TDi Type Engine Alternator - Discovery

Air-operated differential locker for a 24-spline differential, replacing the standard differential centre in the axle. When engaged, it locks both...

Steering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...

Cargo Liner - shaped loadspace floor liner for the Discovery 1 rear load area. The liner drops into the loadspace and covers the original floor co...

Swivel Kit - complete swivel housing overhaul kit for one side of the front axle. The swivel housing ball carries the stub axle and encloses the c...

Swivel Kit - overhaul kit for one front swivel housing assembly. The swivel housing is the steering pivot at the outer end of the front axle case: ...

Swivel Kit - overhaul kit for one front swivel housing assembly. The swivel housing is the steering pivot at the outer end of the front axle case: ...

Steering Damper mounts across the steering linkage to absorb shocks and damp oscillation (bump steer and wheel shimmy) fed back through the track r...

Synchroniser Assembly for 3rd and 4th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The assembly locks the selected gear t...

Brake Calliper Piston and Seal Kit - Rear Axle - overhaul set for the rear brake callipers, part of the rear foundation braking assembly. Calliper...

Front Shock Absorber for the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface. Ga...

Gearbox - LT77 five-speed manual transmission, supplied as a reconditioned complete unit. The LT77 bolts directly to the engine bell housing and d...

EGR Blanking Kit closes off the exhaust gas recirculation (EGR) circuit on the 300 TDi diesel engine. The standard EGR valve feeds a portion of ex...

Upper Clutch Pipe is the rigid metal section of the hydraulic clutch actuation circuit running from the clutch master cylinder. It carries fluid f...

Synchroniser Assembly for 5th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The sliding sleeve is moved by the fifth-gear ...

RR Spring Front Heavy Duty - Discovery Defender

Cylinder Head Assembly for the 2.5L 300 TDi turbocharged diesel engine - the upper closure of the combustion chambers, carrying the valve seats, gu...

Timing Belt Kit - Defender 200TDi

Front Shock Absorber for the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface. Fo...

Swivel Kit 88mm Seals R1 - Discovery 1

Front Shock Absorber fits in the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface....

Service Kit with Oil - Discovery 1 & RRC - 300 TDi

Swivel Kit - overhaul kit for one front swivel housing assembly. The swivel housing is the steering pivot at the outer end of the front axle case: ...

Wheel Arch Trim Kit providing a full six-piece set of extended wheel arch flares that fit over the standard arches. The flares extend approximatel...

Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Bolt for the engine front cover. Hexagon-head threaded fastener securing the timing front cover on the V8 petrol engine. Supplied individually.

Alternator Bearing for the vehicle charging system. This bearing supports the alternator rotor shaft, allowing it to spin freely within the altern...

Coil Spring - Front Right Hand is the front suspension spring for the right-hand side of the vehicle. It seats between the front axle spring pan a...

Panhard Rod Bush Set is a set of polyurethane bushes for the Panhard rod mountings. The Panhard rod locates the axle laterally relative to the cha...

Bump Stop - Yellow

Bump Stop - Rear Radius Arm is a polyurethane compression bump stop for the rear suspension, mounted at the radius arm. It limits axle travel at f...

Rear Coil Spring forms part of the rear suspension, supporting the vehicle's weight at the rear axle. It maintains ride height and absorbs road in...

Spring Isolator seats between the coil spring and its mounting platform in the suspension. It cushions the contact between the spring end and the ...

Wiper Motor Grommet for the rear screen wiper assembly. It seals the aperture in the rear door or tailgate where the wiper motor spindle passes thr...

Front Radius Arm Bump Stop is a travel stop mounted at the front radius arm within the front suspension. It limits axle-to-chassis travel and cush...

Alternator for the V8 EFI petrol charging system, rated at 100A. This is the A127-type alternator assembly, belt-driven from the crankshaft pulley ...

Camshaft Bearing Kit

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Polyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...