Land Rover Discovery 1 Parts

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Heater Hose - Inlet & Outlet is a moulded coolant hose assembly in the heater circuit of the engine cooling system, carrying the combined feed ...

Crankshaft Position Sensor for 4-cylinder petrol applications - 1.8L K Series and 2.0L MPi T Series - mounted at the crankshaft in the engine block...

Bearing transfer box LT230 intermediate shaft

Power Steering Pump - V8

Light Guard Set - protective guards for the rear lamp units, mounted on the rear wings. The guards fit over the rear lamp lenses and shield them a...

Rear Door Lock Assembly - LH - complete latch and lock mechanism for the left-hand rear door, operating within the door locks and handles assembly ...

Mainshaft for the LT77 five-speed manual gearbox, Suffix H specification. The mainshaft is the gearbox output shaft. It carries the synchroniser h...

Front Coil Springs - heavy-duty road springs for the front axle, supplied as a pair. The springs seat between the front axle and the chassis sprin...

O-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.

Intercooler Hose the upper charge-air hose in the intercooler circuit of the 200TDi diesel engine. It carries cooled, pressurised charge air from ...

Radiator Area Retention Clip used in the cooling system assembly. This clip secures cooling system components - including fan cowl panels and radi...

Propshaft Nut - Rear - nut retaining the rear propshaft flange at the rear differential pinion. The nut clamps the propshaft coupling flange again...

Rock guards, rock sliders (pair) galvanised. Fits Discovery 1 and Range Rover Classic (except LSE)

Bonnet Release Cable transmits the pull from the interior bonnet release lever to the bonnet latch. Operating the cabin release lever draws the ca...

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Piston Assembly for the Land Rover 3.5-litre all-aluminium V8 petrol engine. Forms part of the reciprocating assembly within the engine cylinder bo...

Relief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....

Front Housing Gasket - LT77 5-Speed Gearbox This gasket seals the joint between the front housing and the main gearbox casing on the LT77 5-speed ...

Rear Bumper Reflector for the Discovery 1, fitting the designated aperture in the rear bumper to meet lighting regulations. The red retro-reflecti...

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Swivel Pin Thrust Washer - Upper is the shim washer that sits above the upper swivel pin bearing in the front axle swivel housing assembly. It set...

Differential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...

Trailer Plug - a 7-pin towing electrics connector. Wired into the towing vehicle's harness, it mates with the trailer or caravan socket to feed th...

Front bumper end cap, right-hand side, from the front bumper assembly. The end cap closes off the outboard end of the front bumper where the bumpe...

Front Bumper End Cap - Left Hand is the moulded outer closure panel of the front bumper assembly. It fits over the outboard end of the front bumpe...

Copper Sealing Washer - a crush washer used to seal banjo and union connections throughout the diesel fuel system, at fuel pipes, filters and sedim...

Synchromesh Ring for the five-speed manual gearbox mainshaft. The synchro (baulk) ring matches the speed of the gear to the synchro hub before eng...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

Vacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...

Dust Cap for a brake bleed nipple. This small protective cover fits over the bleed screw on a brake caliper or wheel cylinder. It keeps dirt and m...

Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...

Transfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...

Steel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...

Locking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...

Spare Wheel Cover - a soft cover that fits over an externally mounted spare wheel to shield the tyre and rim from dirt, road grime, moisture and UV...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Detent Spring for the LT230 transfer box. It loads the detent that holds the high and low range and differential lock selectors in position, preven...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

lead link pump washer 90/110 used to fit newer style washer pumps to earlier vehicles

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Rear Lamp Guard fits over the rear lamp unit to protect the lens and housing from impact damage. It shields the light cluster from knocks by branc...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Valve spring seat fits both inlet- and exhaust valve springs sold EACH

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...