Land Rover Discovery 1 Parts

Oil Cooler Hose for the engine oil cooling circuit on the V8 engine. Forms part of the hose assembly linking the engine oil cooler to the oil circ...

Middle Floor Crossmember, a transverse structural member beneath the floor pan. This crossmember runs across the underside of the body in the midd...

Rear Floor Crossmember, a transverse structural member beneath the rear load floor. This crossmember runs across the underside of the body and sup...

Door Seal - Rear End Door is the weatherstrip seal for the rear end door. It seals the rear end door aperture against water and draught ingress.

Rear Shock Absorber - a hydraulic damper for the rear suspension, controlling axle movement and wheel oscillation over uneven terrain. Matched to ...

Front Coil Springs for the front suspension, raising ride height by approximately 50mm over standard. Supplied as a pair. The raised height increa...

Flywheel Assembly for the manual transmission on the 2.5L 200 TDi and 300 TDi turbo diesel engines. Bolted to the rear of the crankshaft, the flyw...

Extended Bump Stop - a direct replacement for the standard axle bump stop, mounting to the chassis bracket through two bolt holes. Taller than the...

Upgrade your Land Rover Discovery 1 or Range Rover Classic with these heavy-duty steering arms, designed for superior strength, durability, and ste...

Kickdown Cable for the automatic transmission, part of the gearbox control linkage. The cable links the engine throttle/injection control to the a...

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Half Shaft for the rear axle drive, left-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inne...

Half Shaft for the rear axle drive, right-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inn...

Camshaft - the valvetrain camshaft for the overhead-valve V8. Driven from the crankshaft, its lobes act through the tappets, pushrods and rocker ar...

Exhaust Front Pipe for the exhaust system on 200 TDi diesel applications (non-catalyst, manual transmission). It connects the turbocharger/manifol...

Exhaust Pipe the intermediate section of the exhaust system. It links the front downpipe to the rear silencer and tailpipe, carrying exhaust gas a...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...

Injector Clamp secures a fuel injector into the cylinder head on the 2.5L 300TDi turbo diesel engine. It clamps the injector body down against its...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Viscous Fan Coupling drives the engine cooling fan on the 3.9L and 4.0L V8 EFI petrol engine. The temperature-sensitive coupling varies fan speed ...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Rocker Arm operates on the rocker shaft in the 200TDi diesel valvetrain. Driven by the pushrod, it transfers camshaft motion to actuate the valve.

Wiper Arm - front windscreen, for left-hand-drive applications. It mounts onto the splined wiper spindle and carries the wiper blade, sweeping it a...

Headlight Finisher - left-hand side, supplied primed. This exterior trim panel frames the headlamp unit on the front of the vehicle, locating betwe...

Headlight Finisher - right-hand side, supplied primed. This exterior trim panel frames the headlamp unit on the front of the vehicle, locating betw...

Rear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...

Limited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Winch Bumper Fitting Kit - the mounting hardware set for installing the DA5621 steel winch bumper. Supplies the fixings needed to attach the bumpe...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Rear Body Mount secures the rear body tub to the rear chassis crossmember, maintaining body-to-chassis alignment and damping vibration. Steel, sup...

Air Filter - air filter for the 3.5 V8 carburettor engine, fitted at the carburettor intake to filter incoming air before it is drawn through the c...

Waterproof Front Seat Cover Set (Black) - tailored covers for the two front seats. Constructed from hard-wearing woven polyester with a PVC backin...

Differential Pan Cover - weld-in replacement cover for the axle differential housing, incorporating a filler/level plug. The cover welds onto the ...

Headlamp Surround - the front-end finisher that frames the left-hand headlamp unit, locating between the headlamp aperture and the grille panel. I...

Headlamp Surround - the front-end finisher that frames the right-hand headlamp unit, locating between the headlamp aperture and the grille panel. ...

Boot Centre Floor Panel is a rear body repair panel forming the centre section of the boot floor within the rear load area structure. It is a stru...

Front Coil Spring for the front suspension, fitted on the left-hand side. It seats between the chassis spring seat and the front axle, supporting ...

Bumper assy rear Disco 1 FROM MA

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Clutch Master Cylinder - the pedal end of the clutch hydraulic circuit. Actuated by the clutch pedal pushrod, it generates the hydraulic pressure t...

Front Coil Spring - part of the front road suspension, left-hand side. The spring seats between the lower suspension link and the chassis spring se...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...