Land Rover Discovery 1 Parts

Pedal Rubber Pad for the foot pedal. The moulded rubber pad slips over the pedal arm to provide a durable, non-slip foot surface. Fitted to manual...

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Brake Pad Retention Kit - front brake pad retaining hardware for the disc brake assembly. Secures the front brake pads in the caliper on installat...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Automatic Drive Belt Tensioner for the front-end accessory drive system, maintaining correct tension across the auxiliary belt that drives the alte...

Thermostat for the 2.5L 200TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. This thermostat opens at ...

Stub axle

Gearbox Filter for the LT77 five-speed manual gearbox. This gauze oil strainer sits in the gearbox lubrication circuit, screening the oil drawn thr...

Joint washer

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Bottom Overhaul Gasket Set for the 3.5 V8 petrol engine. The set supplies the gaskets and seals used to reseal the lower engine once the sump is r...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Gear Lever Knob for the LT77 5-speed manual gearbox. Fits the main gear lever of LT77-equipped vehicles, including V8 petrol manual variants. The ...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Joint Washer - 4-Wheel ABS installed at the stub axle interface in the hub assembly of vehicles equipped with 4-wheel ABS. This asbestos-free gask...

Drive Belt - 10mm × 1025mm for the auxiliary drive system on the 2.5L 4-Cylinder diesel and 200TDi engines. This poly-V ribbed belt drives the alt...

Front Axle CV Joint, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft and transmits ...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

Front door window regulator assembly for left-hand front door applications within the door glass operating mechanism. This component forms part o...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Speedo drive oil seal LT230

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Upper Spring Isolator for the coil spring suspension. This rubber seat sits at the upper end of the coil spring, between the top of the spring and ...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Diesel Fuel Filter - replaceable cartridge filter element for the fuel supply circuit on 200 TDi and 300 TDi diesel engines. The element sits in t...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...