Land Rover Discovery 1 Parts

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Brake lever kit

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Oil Drain Pipe Gasket for the turbocharger oil return line on the 300TDi 2.5L turbo diesel engine. It seals the flanged joint where the external o...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Relay

Clevis pin

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Bolt Threaded fastener used within the exhaust system assembly.

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

Yoke Transmission

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Rocker Assembly Aluminium - LH

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Shaft coupling

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Camshaft Sprocket - GEMS V8 is the timing chain sprocket fitted to the camshaft of the Rover GEMS 4.0L and 4.6L V8 petrol engine. The sprocket is ...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...