Land Rover Discovery 1 Parts

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Rear Propshaft Rubber Coupling - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while ab...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Ignition heater plug timer glow plug relay

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...

Door glass channel

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Rear brake shield RH

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Steering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...

Plenum hose

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Steering UJ upper

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Drain plug

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

This steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...

Repair kit for clutch master cylinder, fits to AEU1714, ANR2651.

Exhaust mounting spacer tube

Exhaust Valve for the Rover V8 EFI petrol engine, fitted in the cylinder head valvetrain. The valve seals the exhaust port during the combustion c...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Cooling Fan for the 2.5L 300 TDi turbo diesel engine, forming part of the engine cooling assembly. The fan is driven from the front of the engine ...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 200 TDi 2.5L turbo diesel engine. It forms a coolant-tight...

Carburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...

Ensure accurate engine timing with this 12-piece timing tool kit, designed for Land Rover 2.5D, 200TDI, and 300TDI engines. This comprehensive kit ...

Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...

Distributor Lead for the ignition system of the 3.5L V8 petrol engine. This lead connects the distributor to the ignition amplifier module, adapti...

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Air Filter Element is the replaceable filtration element of the engine air intake system. It seats inside the air cleaner housing and traps dust an...

Torsional Vibration Damper mounting on the crankshaft nose of the 200Tdi 2.5L four-cylinder turbo diesel engine. Also serving as the crankshaft pu...

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

Cylinder Head Gasket for the Rover V8 petrol engine, sealing the joint between one cylinder head and the engine block. It seals the combustion cha...

Cylinder Head Bolt (Long) for the V8 petrol engine, securing the cylinder head to the engine block. This is the longer of the two head bolt length...