Land Rover Discovery 1 Parts

Suspension Kit providing 2 inches of lift in a medium load configuration, combining rated coil springs with extended-travel Pro Sport shock absorbe...

Alloy Wheel, 18 x 8 with ET20 offset and a 5 x 165.1 mm (five-stud) bolt pattern, finished in black. The wheel forms the mounting interface betwee...

Differential Pinion Flange Kit for the three-bolt drive flange on the axle differential. The pinion flange mounts on the differential pinion shaft...

Automatic Transmission Oil Pump for the 4-speed automatic gearbox, part of the transmission's internal hydraulic system. The pump sits at the fron...

Turbo Oil Drain Pipe returns lubricating oil from the turbocharger bearing housing to the crankcase. Fitted between the underside of the turbochar...

Heater Hose - Coolant Valve is a moulded coolant hose in the heater circuit of the engine cooling system. It connects the heater control (coolant)...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Transfer Case Cover for the LT230 transfer case assembly, sealing the main housing against contamination and retaining the internal lubricant. The...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Sealing Washer seals the turbocharger oil drain pipe where it meets its adaptor on the engine block. It forms an oil-tight joint in the turbocharg...

Bolt - 1/4" UNC x 1-7/8" is a UNC hex head bolt used in the engine cooling and air conditioning systems of Land Rover vehicles fitted with the 3.5L...

Front Brake Caliper Piston Kit for vehicles fitted with solid front brake discs. It operates within the front disc brake caliper assembly, renewing...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Spring Clip - Steel for V8 EFI petrol engines, used in the throttle linkage and gear change mechanism. This steel spring clip provides positive re...

Brake Caliper Bolt secures the rear brake caliper to its mounting bracket within the rear braking assembly. It clamps the caliper body in position...

Screw - M8 x 25mm is a fastener used in the assembly of the LT230 transfer gearbox. The LT230 is a two-speed transfer box fitted to Defender, Disc...

Camshaft Washer is a retaining washer used at the front of the camshaft within the timing drive of the 3.5L V8 petrol engine. It is fitted at the ...

Interlock Retainer for the LT77 five-speed manual gearbox gearchange. It holds the selector interlock components within the selector and yoke assem...

Washer 577254

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Bolt rear caliper 7/16" UNF

Needle Bearing - LT77 supports a mainshaft gear on the LT77 5-speed manual gearbox mainshaft, allowing the gear to rotate freely on the shaft. It ...

O-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.

O-Ring seals the intermediate shaft in the LT230 transfer box, sitting between the shaft mounting and the transfer casing to hold the oil seal at t...

Anti-Roll Bar Bush for the front suspension system, sold as a pair. This bush locates the anti-roll bar at its chassis mounting points, allowing t...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Nyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...

Locking Wheel Nut Set for alloy wheels, comprising four locking nuts that replace standard wheel nuts to deter wheel theft. Thread size 16 x 1.50;...

Oil Pump Rotor Set - Inner & Outer for the 300TDi engine, fitted to the Defender, Discovery 1, and Range Rover Classic. The oil pump rotor set...

Needle Bearing - LT77 5-Speed Gearbox - Mainshaft This needle roller bearing supports the mainshaft gear cluster within the LT77 5-speed manual ge...

Centre Plate Gasket for the LT77 5-speed manual gearbox. This gasket seals the joint between the main casing sections of the LT77 gearbox, prevent...

Oil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Turbocharger to Intercooler Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit. This hose connects the turbocharger compresso...

Swivel Pin Bush - Upper is the upper pivot bush in the front axle swivel housing assembly. It seats in the top of the swivel housing and locates t...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Hex Nut

Bulb and Holder for switch and control panel illumination. The orange-tinted bulb and its integral holder fit into the rear of dashboard switches ...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Seat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...