Land Rover Discovery 1 Parts

Reservoir bracket

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Clutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...

Camshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Flanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...

Drive Flange Nut - Front secures the front drive flange (driving member) to the wheel hub, as part of the front hub assembly. It retains the drivi...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Head Gasket - Metal for the 3.9L V8 EFI engine, sealing the cylinder head to the engine block in the top-end assembly. This multi-layer steel head...

Piston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Handbrake Expander Assembly for the drum-type transmission (parking) brake mounted at the rear output of the transfer box. The expander sits betwe...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Screw for use in Land Rover body, chassis, and hardware applications.

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

Front Caliper Fixing Bolt with 7/16 UNF thread, used to secure the front brake caliper to its mounting bracket. This bolt is a safety-critical fast...

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Axle Casing Stud for the front and rear axle case assemblies. It is a threaded stud used to secure components to the axle casing on the Land Rover...

Swivel Pin Kit - Upper for the front axle swivel pin housing assembly. The upper swivel pin forms the top pivot about which the swivel housing rota...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Steering Damper Relocation Kit enables the steering damper to be repositioned from the track rod to the drag link - the mounting position used on t...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Twin Shock Mount Kit - Rear provides the additional mounting points required to run twin rear shock absorbers on each side of the rear axle. The ad...

Suspension Kit providing 2 inches of lift in a heavy load configuration, combining rated coil springs with All Terrain shock absorbers. The heavy ...

Suspension Kit providing 2 inches of lift in a medium load configuration, combining rated coil springs with All Terrain shock absorbers. Designed ...

Terrafirma All Terrain Suspension Kit - Light Load, +2" (50mm) Lift for Defender 90, Discovery 1 and Range Rover Classic. This is a RAISED suspens...

Shock Absorber - rear suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and rear a...

Shock Absorber - front suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and front...

Shock Absorber for the rear coil spring suspension system. This big-bore unit is designed for heavily laden and expedition applications where sust...

Big Bore Expedition Shock Absorber - front position, standard ride height. The damper installs between the front axle mounting and the chassis bra...

Rear Coil Spring - Heavy Duty, +2" Lift A rear suspension coil spring from the Terrafirma range, seating between the axle and the chassis spring s...

12N 7-Pin Trailer Socket for the towing electrical system, mounted at the rear of the vehicle. The 12N socket carries the standard trailer road-li...

Window Regulator - Rear raises and lowers the rear door glass, mounting inside the door and linking the window motor to the glass carrier. This is...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

decoke set OEM 300tdi without headgasket

Heater Matrix for the cabin heating system, mounted within the heater box assembly. Engine coolant is circulated through the matrix core, and the ...

Handbrake Adjuster for the rod-operated transmission parking brake mounted on the LT230 transfer box. On these vehicles the handbrake acts on a dru...

Fuel Injector Pipe for the high-pressure injection circuit of the 300 TDi 2.5L diesel engine. This rigid steel pipe carries metered high-pressure ...

Injector Pipe Kit - set of 4 high-pressure fuel pipes for the 300Tdi 4-cylinder turbo diesel engine, mechanical injection pump variant (Less EDC). ...

Injector Pipe - number-one cylinder high-pressure injector pipe for the 2.5L 300 TDi turbo diesel. This rigid steel pipe carries diesel at injecti...

Handbrake Cable for the parking brake system. It connects the handbrake lever to the parking brake mechanism, transmitting the lever movement that ...