Land Rover Discovery 1 Parts

Differential Bearing Shim - 0.063in

Seat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...

Exhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Switch window lift

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Steering Shaft - the intermediate shaft in the steering column assembly. It links the steering column to the steering box input, transmitting rotat...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Exhaust Manifold Heat Shield mounts over the exhaust manifold to protect surrounding components from radiant heat. It deflects heat away from adja...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Door Glass Channel the glass run channel within the door assembly. The channel guides the door glass as it is raised and lowered by the window reg...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Bulb & Holder - Green, an illumination bulb supplied in its colour-coded green holder for the dashboard and switch panel lighting circuits. Th...

O-Ring seals the joint between the sump and the ladder-frame assembly on the 2.5L 200TDi diesel engine.

Throttle Spring - the return spring in the throttle linkage. Acting on the throttle body spindle, it closes the throttle butterfly and returns the ...

Accelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine (reconditioned). The injector atomises high-pressure diesel delivere...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...

Hose Clip clamps a hose onto its spigot or fitting, maintaining a sealed joint under pressure.

Cross Rod End

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Front Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On

Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Track Rod Washer from the steering linkage. It seats at the track rod fixing, spreading clamp load beneath the retaining nut to secure the joint.

Bolt securing the exhaust manifold on the Rover V8 petrol engine. A 3/8" UNC x 1 1/8" fastener used to retain the exhaust manifold to the cylinder...

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

rock slider, rock guards (pair) BA 2091 Generic picture, the set supplied is BLACK coated, NOT galvanised.

Cylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...

Axle Spring Mount forms the lower seat for the rear coil spring, welding onto the rear axle casing to locate and retain the base of the spring. Th...