Land Rover Discovery 1 Parts

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Rubber Mounting for the body-to-chassis mounting points. The rubber is fitted under the body mounting bolt, seated between the body and the chassis...

Accelerator Cable for the 200TDi throttle linkage. The cable runs from the accelerator pedal to the throttle lever on the fuel injection pump. Dep...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...

Oil seal 12.5mm OEM

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Spring bonnet pull cable return

Clip

Dipstick tube O-ring 200 & 300TDi, TD5

Air Filter Element installed in the air cleaner housing of the 200Tdi 2.5L four-cylinder turbo diesel engine. The element filters intake air upstr...

Oil Filter Adaptor Gasket Seals the oil filter adaptor housing to the cylinder block within the lubrication circuit of the 300 TDi 2.5L diesel engi...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Flanged Head Screw, M8 x 12 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loo...

Crankcase breather T-piece with restrictor V8 EFI

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Clevis Pin - a linkage pin used in the accelerator and throttle control. It joins the throttle cable clevis to its operating lever, allowing the l...

Bolt - 1/2" UNF x 6-1/4", part of the front radius arm chassis mounting. The long shank passes through the radius arm front bush and the chassis m...

Collapsible spacer transfer box

Cylinder Head Bolt for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the engine block, cla...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Trim Rivet, an 8 x 20mm plastic drive (pin-type) rivet used to secure trim panels and mouldings to the body, typically wheel arch trims, bumpers an...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Caliper Seal - internal bridge seal for the front brake caliper. This O-ring sits between the two halves of the caliper body and seals the fluid pa...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Rear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Ignition heater plug timer glow plug relay

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...

Heater Hose - Outlet - V8 forms part of the heater coolant circuit on V8 petrol applications. It carries coolant from the heater matrix outlet bac...

Door Glass Channel - Lift - Front - D1/RRC

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Bolt - Front Radius Arm is the M16 x 100 mm grade 10.9 high-tensile bolt that secures the front radius arm within the front suspension linkage. It...

Exhaust Mount Washer

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...