Land Rover Discovery 1 Parts

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Cigar Lighter - the panel-mounted lighter and 12V accessory socket in the instrument panel electrical system. The assembly comprises a socket and ...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Silicone Intercooler & Turbo Hose Kit - a set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing the standard...

Rear Lamp Bulb Holder Double-pole bulb holder that seats in the rear lamp housing, retaining the bulb and carrying the electrical contacts between ...

Bottom cover seal

Body Mounting Kit renews the body-to-chassis mounting points, where the body is located and secured to the chassis frame. The rubber mounts isolat...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Brake Pad Set for the front axle disc brake assembly, for use with vented front discs. The pads locate within the front calipers and clamp against ...

Decoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...

Brake Pad Set for the rear axle disc brake assembly. The pads locate within the rear calipers and clamp against the rear discs, generating the fric...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. It cradles the anti-roll bar at its ...

Spring Retaining Plate in the rear suspension, securing the upper end of the rear coil spring. It locates and clamps the top of the coil spring ag...

Spring Retaining Plate Front coil spring retaining plate that clamps over the top of the spring at its seat, holding the spring captive so it canno...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Wheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Breather hose rocker cover

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Banjo Bolt for the fuel and oil circuits, used to secure a banjo union to its housing while allowing fluid to pass through the cross-drilled body. ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Shock Dropper - Rear - Pair: zinc-plated steel relocated rear shock absorber top mounts that lower the upper mounting point by 50mm. By relocating...

Flange Bolt, M8 x 120 mm - a hexagon-head flange bolt that secures the coolant (water) pump on the 300TDi 2.5-litre turbo diesel engine. The integ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Window Lift Switch is the control switch within the electric window circuit. Fitted to the door trim or centre console, it directs current to the ...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Spill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Bolt - a hexagonal-head bolt with a 1/4" UNF (Unified Fine) imperial thread and a 1-1/4" length. Used as a body and chassis fixing at points such a...