Land Rover Discovery 1 Parts

Sump Gasket for the 2.0L MPI T-Series 4-cylinder 16-valve petrol engine, sealing the oil sump to the underside of the cylinder block. It forms the...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Wash Wipe Switch for the steering column switchgear. This column-mounted stalk operates the windscreen wipers and the windscreen washer. It mounts...

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Radiator Hose - Bottom - V8 Petrol

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Cap Reservoir Br.m.cylinder

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Hose Clip for radiator hose connections on 4-cylinder TDi diesel engines. This screw-type hose clip secures the upper and lower radiator hoses at ...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Bottom Hose is the lower radiator hose in the engine cooling circuit. It carries coolant from the base of the radiator back to the water pump inle...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

High Note Horn - the higher-pitched element of the dual-tone warning horn assembly. Mounted behind the front grille or valance and paired with a l...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...