Land Rover Discovery 1 Parts

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Stepper Motor - idle air control valve for the V8 multi-point fuel injection system. Mounted on the plenum chamber, it meters the air bypassing th...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Stub axle oil seal inner

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Grommet

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Automatic Transmission Oil Screen Kit for the ZF 4-speed automatic transmission, serving the fluid filtration circuit within the transmission sump....

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Front Hub Lock Washer for the front hub and driveshaft assembly. This tabbed washer seats between the hub nut and the hub bearing assembly on the ...

Rocker Cover Gasket for the 2.5L 200TDi diesel engine, sealing the joint between the rocker cover and the cylinder head. Installed at the top of t...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. O-ring is included. ...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Hub mud shield

Manifold gasket 300TDI

Timing Chain for the Rover V8 petrol engine, part of the camshaft drive assembly located in the front timing cover. This single-row roller chain t...

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Power steering seal kit

Exhaust Rubber Mounting suspends the exhaust system from the chassis, supporting the silencer and pipework at its mounting points. The rubber elem...

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Enhance the ignition performance of your Land Rover Defender, Discovery 1, and Range Rover Classic (3.5 V8 carb & EFI models) with this high-qu...

Clip is a multi-purpose retaining clip used to secure cables, harnesses and small components in their mountings. It locates and holds items such a...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...