Land Rover Discovery 1 Parts

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Front Crankshaft Oil Seal for the 2.5L 300TDi turbo diesel engine. It fits around the crankshaft nose at the front of the engine, sealing the point...

Viscous Fan Coupling Spanner Set, a pair of thin-section spanners (32 mm and 36 mm) for removing and refitting the viscous fan coupling at the wate...

Reverse Light Switch for the R380 5-speed manual gearbox, completing the reverse lamp circuit when reverse gear is engaged. This switch threads in...

Transfer Box Gear Change Bush for the LT230 transfer box gear change and differential lock linkage. This bush fits the gear change linkage connect...

Flanged Screw, M8 x 25 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loosenin...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Radius Arm Bolt - hexagon head bolt securing the rear radius arm at the axle and chassis mounting points within the rear suspension assembly. This...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Polyvee auxiliary drive belt used in the engine front-end cooling fan and ancillary drive system. The belt transmits rotational drive from the cra...

Bump Stop - Front for the front suspension travel limiting assembly. This rubber bump stop limits upward suspension travel at the front axle, prov...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Brake Pad Set for the rear axle disc brakes, fitting the rear brake calipers. The friction pads clamp against the rear brake discs under caliper a...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Timing Belt Kit with Tensioners for the 300 TDi 2.5L turbo diesel engine. The kit serves the timing belt drive - the toothed-belt system that synch...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Vacuum Pump Gasket for the 2.5L 300TDi diesel engine, sealing the vacuum pump mounting face to the cylinder block. The vacuum pump is driven from ...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Rear Upper Shock Absorber Bracket, the upper mounting bracket for the rear damper within the rear suspension. It forms the fixed upper anchorage b...