Land Rover Discovery 1 Parts

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Ball joint kit for the steering box drop arm within the steering linkage assembly. The joint installs in the drop arm on the steering box output ...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

gasket throttle body V8 EFI D2, P38

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Voor LT77 versnellingsbak

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Drive Belt is the auxiliary drive belt for the 3.5L V8 petrol engine. Running from the crankshaft pulley, it drives the alternator and, where fitt...

Power Steering Belt (Vee drive belt) for the 3.5L V8 petrol engine accessory drive. This belt runs between the crankshaft pulley and the power ste...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Oil Cooler Pipe - the pipe carrying engine oil from the engine to the oil cooler within the lubrication cooling circuit of the 2.5L 4-cylinder TDi ...

Oil Cooler Pipe - the pipe carrying engine oil between the oil cooler and the engine within the lubrication cooling circuit of the 2.5L 4-cylinder ...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

EGR Blanking Kit replaces the exhaust gas recirculation (EGR) valve on the 300 Tdi engine, sealing the EGR port on the intake manifold so exhaust g...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Brake pad retention kit for STC2956, STC9187

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Headlamp washer jet RRC Discovery 1

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Hex Nut with a 7/8" UNF (Unified National Fine) thread, used on the power steering box assembly. This large six-sided fastener threads onto a matc...

Spring Retainer - rear inner-top retainer in the coil spring and shock absorber mounting. It locates and holds the top of the rear coil spring at ...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Bypass Hose for the engine cooling system of the 200 TDi diesel engine, connecting into the coolant pump. It carries coolant on the bypass route t...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Propshaft bolt kit Defender D1 RRC

Clutch release fork kit used within the manual transmission clutch release mechanism. The release fork operates in the clutch housing and transfers...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...