Land Rover Discovery 1 Parts

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Oil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...

Complete Cylinder Head for the 300 TDi 2.5L diesel engine, supplied fully assembled and ready to fit. The head is delivered built up with the valv...

bush shock absorber OEM, bush anti roll bar OEM

Cable Clip for securing and routing cables and wiring to body and chassis structures.

The Maxtrac Blindo 16x7 alloy wheel is designed for off-road durability and rugged performance, making it the perfect choice for Land Rover and 4x4...

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Brake Master Cylinder - ABS is the tandem master cylinder at the head of the hydraulic braking circuit, specified for the servo-assisted anti-lock ...

Main bearing kit 0.020" undersize OEM AE

Power steering pipe forming the low-pressure return leg of the power steering hydraulic circuit, running from the steering box return port back to ...

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Heater Hose - Inlet & Outlet is a moulded coolant hose assembly in the heater circuit of the engine cooling system, carrying the combined feed ...

Crankshaft Position Sensor for 4-cylinder petrol applications - 1.8L K Series and 2.0L MPi T Series - mounted at the crankshaft in the engine block...

Bearing transfer box LT230 intermediate shaft

Power Steering Pump - V8

Light Guard Set - protective guards for the rear lamp units, mounted on the rear wings. The guards fit over the rear lamp lenses and shield them a...

Rear Door Lock Assembly - LH - complete latch and lock mechanism for the left-hand rear door, operating within the door locks and handles assembly ...

Spring Dislocation Cones - Front are fitted inside the front coil springs to prevent spring dislocation under maximum suspension droop. During extr...

Mainshaft for the LT77 five-speed manual gearbox, Suffix H specification. The mainshaft is the gearbox output shaft. It carries the synchroniser h...

Rear Gas Shock Absorber - a gas-charged hydraulic damper for the rear suspension, controlling axle movement over road and off-road terrain. Matche...

Front Coil Springs - heavy-duty road springs for the front axle, supplied as a pair. The springs seat between the front axle and the chassis sprin...

Fuel Pipe Assembly - part of the fuel delivery circuit for the carburettor V8. It carries fuel from the fuel supply line to the SU carburettors, fe...

O-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.

Intercooler Hose the upper charge-air hose in the intercooler circuit of the 200TDi diesel engine. It carries cooled, pressurised charge air from ...

Radiator Area Retention Clip used in the cooling system assembly. This clip secures cooling system components - including fan cowl panels and radi...

Fuel Tank Inspection Plate Seal is a rubber sealing gasket for the fuel tank inspection plate in the fuel tank assembly. The inspection plate prov...

Propshaft Nut - Rear - nut retaining the rear propshaft flange at the rear differential pinion. The nut clamps the propshaft coupling flange again...

Rock guards, rock sliders (pair) galvanised. Fits Discovery 1 and Range Rover Classic (except LSE)

Clutch Release Pivot for the clutch release mechanism, mounted inside the bellhousing. The pivot provides the fulcrum on which the clutch release ...

Differential Pinion Shim - 0.062" selective shim used to set the pinion position within the differential (final drive) assembly. Fitted at the pin...

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Bonnet Release Cable transmits the pull from the interior bonnet release lever to the bonnet latch. Operating the cabin release lever draws the ca...

Locking Washer for the swivel pin housing, fitted at the lower swivel pin. Its tab is folded against the retaining bolt to lock the fixing and prev...

O-Ring for the ZF automatic gearbox oil pump, sealing the pump housing within the gearbox casing. The ZF oil pump is an internally-driven unit tha...

Water Pump Pulley for the 2.5L 300 TDi turbocharged diesel engine, mounting to the water pump hub within the engine cooling circuit. The pulley is...

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Piston Assembly for the Land Rover 3.5-litre all-aluminium V8 petrol engine. Forms part of the reciprocating assembly within the engine cylinder bo...

Alloy Wheel, 16 x 7 inch, finished in gloss black. The wheel has a positive offset of ET+11 (11 mm) and a rated load capacity of 1,400 kg per whee...

Injector Dowel Ring for the fuel injection system of the 2.5L 200 TDi engine. This locating dowel positions the injector correctly in the cylinder...

Relief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....

Seal

Rear Bumper Mounting Bracket, part of the rear bumper assembly. The bracket bolts to the rear of the chassis and carries the rear bumper, transfer...

Front Housing Gasket - LT77 5-Speed Gearbox This gasket seals the joint between the front housing and the main gearbox casing on the LT77 5-speed ...

Rear Bumper Reflector for the Discovery 1, fitting the designated aperture in the rear bumper to meet lighting regulations. The red retro-reflecti...

Pivot Lever Pin is the selector pivot pin in the LT230 transfer box, providing the pivot point about which the range selector lever swings. It loc...

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Swivel Pin Thrust Washer - Upper is the shim washer that sits above the upper swivel pin bearing in the front axle swivel housing assembly. It set...

Oil Pump Bolt for the Rover 3.5L V8 petrol engine, 1/4" UNC x 1 1/4". The bolt secures the oil pump to the timing cover, retaining the pump body th...