Land Rover Discovery 1 Parts

Exhaust Rear Assembly the intermediate and rear section of the exhaust system for the 3.5L V8 EFi engine in non-catalyst configuration. It carries...

Fuel Gauge Sender Unit measures the fuel level in the tank and signals the dashboard fuel gauge. Mounted in the fuel tank, its float and variable ...

Drive Belt for the accessory drive on the 3.9L V8 EFI petrol engine in the configuration without air conditioning. This multi-ribbed poly-vee belt...

Air Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...

Turbocharger for the forced-induction system of the 2.5L 300 TDi diesel engine, supplied complete with the mid manifold section. Driven by exhaust...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...

Valve Spring for the cylinder head valvetrain. Fitted over the valve stem, it holds the valve closed against its seat and keeps the follower in con...

Injector Clamp secures a fuel injector into the cylinder head on the 2.5L 300TDi turbo diesel engine. It clamps the injector body down against its...

Power Steering Pump Pulley mounts on the power steering pump within the engine's auxiliary drive on the 2.5L 300TDi turbo diesel. Driven by the au...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Viscous Fan Coupling drives the engine cooling fan on the 3.9L and 4.0L V8 EFI petrol engine. The temperature-sensitive coupling varies fan speed ...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Engine Piston for the 2.5L 300 TDi diesel engine, supplied in standard bore size. The piston runs in the cylinder bore and transfers combustion pr...

Front Crankshaft Oil Seal seals the front of the crankshaft where it passes through the timing cover. It prevents oil loss at the crankshaft pulle...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Rocker Arm Bush is the bearing bush pressed into the rocker arm, carrying it on the rocker shaft. Fitted to 200TDi and 300TDi diesel valvetrains.

Rocker Arm operates on the rocker shaft in the 200TDi diesel valvetrain. Driven by the pushrod, it transfers camshaft motion to actuate the valve.

Inlet Valve seats in the cylinder head of the 3.5L and 3.9L V8 petrol engine. It controls the intake charge entering the combustion chamber on twi...

Wiper Arm - front windscreen, for left-hand-drive applications. It mounts onto the splined wiper spindle and carries the wiper blade, sweeping it a...

Headlight Finisher - left-hand side, supplied primed. This exterior trim panel frames the headlamp unit on the front of the vehicle, locating betwe...

Headlight Finisher - right-hand side, supplied primed. This exterior trim panel frames the headlamp unit on the front of the vehicle, locating betw...

Rear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...

Limited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Winch Bumper Fitting Kit - the mounting hardware set for installing the DA5621 steel winch bumper. Supplies the fixings needed to attach the bumpe...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Rear Body Mount secures the rear body tub to the rear chassis crossmember, maintaining body-to-chassis alignment and damping vibration. Steel, sup...

Air Filter - air filter for the 3.5 V8 carburettor engine, fitted at the carburettor intake to filter incoming air before it is drawn through the c...

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

Waterproof Front Seat Cover Set (Black) - tailored covers for the two front seats. Constructed from hard-wearing woven polyester with a PVC backin...

Stainless Braided Brake Hose Kit - a set of flexible brake hoses for the hydraulic braking circuit, supplied in +40mm extended lengths for vehicles...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Differential Pan Cover - weld-in replacement cover for the axle differential housing, incorporating a filler/level plug. The cover welds onto the ...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.

Headlamp Surround - the front-end finisher that frames the left-hand headlamp unit, locating between the headlamp aperture and the grille panel. I...

Headlamp Surround - the front-end finisher that frames the right-hand headlamp unit, locating between the headlamp aperture and the grille panel. ...

Front Twin Shock Tower (Pair) - an uprated front shock absorber mounting set for coil-sprung suspension that allows a second shock absorber to be f...

Steering Guard - a heavy-gauge steel skid plate that bolts beneath the front of the chassis to shield the steering linkage and steering damper from...

Front Bumper End Cap finishes the right-hand outer end of the front bumper assembly. The end cap closes off the corner of the bumper where it wrap...

Front Bumper End Cap for the left-hand side, part of the front bumper assembly. Moulded cap that fits over the outer LH end of the front bumper, c...

Interior Mirror & 2 - Discovery 1

Boot Centre Floor Panel is a rear body repair panel forming the centre section of the boot floor within the rear load area structure. It is a stru...