Land Rover Discovery 2 Parts

O-Ring for the Td5 fuel pressure regulator. This O-ring seals the fuel pressure regulator within the Td5 fuel system, maintaining a leak-tight joi...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Starter Motor for the Td5 2.5L 5-cylinder turbo diesel engine, operating within the engine electrical starting system. On ignition the solenoid-ac...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Drain plug LT77 R380

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Polyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...

Water Pump O-Ring Set provides the sealing rings for the coolant pump, sealing the pump to its mounting face and preventing coolant leakage at the ...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Stud M8 x 25

Dipstick tube O-ring 200 & 300TDi, TD5

Selector yoke spherical bush

Drive Belt Idler Pulley for the auxiliary (accessory) belt drive of the Td5 2.5L 5-cylinder turbo diesel engine. The pulley mounts above the water...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Bleed Screw - Blue Anodised Aluminium for the coolant bleed point on Td5 engines. The screw seats in the bleed port on the top coolant hose and is...

Air flow meter TD5 replacement

Fuel block connector assembly (with hose) TD5

Head gasket set 3.9 EFI MA on

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Radiator Mount is a moulded rubber isolator in the engine cooling system, forming part of the radiator mounting. It locates the radiator within it...

Dzus Fastener is a quarter-turn quick-release stud used to secure the radiator cowl and cooling fan shroud within the engine cooling assembly. The...

Crankshaft Damper mounts on the nose of the crankshaft and forms part of the front-end accessory drive on the Td5 2.5L 5-cylinder turbo diesel. It...

Repair kit adjuster hand brake

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Oil seal

Head bolt kit TD5

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Ignition heater plug timer glow plug relay

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Bleed Screw for the coolant bleed point on Td5 engines. The screw seats in the bleed port on the top coolant hose and is opened to release trapped...

Oil Pump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the oil pump to its mounting face on the engine. It forms the oil-tight j...

Inlet Manifold Gasket for the Rover V8 petrol engine, sealing the inlet manifold where it seats in the valley between the two cylinder banks. This...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Fan Bearing supports the engine cooling fan on the Td5 front cover. Mounted to the timing cover, the bearing carries the viscous cooling fan and i...