Land Rover Discovery 2 Parts

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Coolant Hose connecting the heater circuit to the oil cooler on the Td5 2.5L five-cylinder turbo diesel. The hose carries engine coolant along the...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Wiper Blade A front windscreen wiper blade within the wiper assembly. It attaches to the wiper arm and clears the windscreen as the arm sweeps acro...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Brake Caliper for the rear braking assembly, mounted on the right-hand side. The caliper houses the piston and hydraulic fluid inlet, converting p...

tank expansion, WITHOUT CAP!

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Starter Motor Repair Kit for the solenoid on the Td5 starter motor (NAD101240). The kit renews the solenoid's copper contacts and plunger - the pa...

Grommet

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Drain plug LT77 R380

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Engine Mount - Rubber - Diesel supports the engine on the chassis and isolates it from the vehicle structure. The bonded rubber element absorbs co...

Output Shaft Seal for the extension housing of the ZF 4-speed automatic gearbox. The seal fits at the rear of the gearbox, where the output shaft ...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Air Spring Retainer Clip

Oil Filter for the Td5 2.5L five-cylinder turbo diesel. Part of the engine lubrication system. The filter is a replaceable cartridge element that ...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Glow plug TD5

O-Ring for the Td5 fuel pressure regulator. This O-ring seals the fuel pressure regulator within the Td5 fuel system, maintaining a leak-tight joi...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Anti-Roll Bar Bush for the Active Cornering Enhancement (ACE) actuator mounting within the suspension stabiliser assembly. In an ACE-equipped syst...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Foam Pad - Air Intake Deflector seals the air intake deflector in the scuttle area, where fresh air is drawn into the heating and ventilation syste...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

High/Low Lever Gaiter - the flexible boot that seals the transfer box high/low range selector lever where it passes through the centre console. Fi...

Selector yoke spherical bush

Bumper Lamp rear left-hand assembly, part of the rear bumper lighting cluster. The unit combines the reverse lamp and rear fog lamp in a single ho...

Polyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...

Drive Belt Idler Pulley for the auxiliary (serpentine) drive belt system of the V8 petrol engine. The idler guides the belt and maintains its runni...

Water Pump O-Ring Set provides the sealing rings for the coolant pump, sealing the pump to its mounting face and preventing coolant leakage at the ...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...