Land Rover Discovery 3 Parts

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Timing gear lower idler pulley for the engine timing drive system. This pulley guides and stabilizes the timing belt within the lower timing gear...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Axle oil filler plug, sealing the combined fill and level aperture in the axle casing. Used at both front and rear axle positions. The plug closes...

Axle oil drain plug, sealing the drain aperture at the base of the axle casing. Used at both front and rear axle positions. The plug is removed to...

Valve Body Adaptor - connects the valve block (main control) to the vacuum control valve on the ZF 6HP26 and 6HP28 six-speed automatic transmission...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Final Drive Lubricant - a fully synthetic 75W-90 gear oil meeting API GL5, supplied in a 4 litre pack. Specified for the front and rear final driv...

Fuel Filler Restrictor for diesel vehicles, fitted inside the fuel filler neck as part of the fuel tank and filler assembly. It forms a physical b...

Trim clip used to retain trim panels to the body structure. Size 8.5 mm, with a panel grip range of 0.8 to 2.2 mm. The clip locates through the pa...

Expansion Tank Seal - sealing ring for the bleed valve fitted to the coolant expansion tank in the engine cooling system. Seals the bleed valve in...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Oil Sump Gasket seals the oil pan (sump) to the cylinder block on the V6 diesel engine. It maintains an oil-tight joint at the base of the engine,...

Bolt

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

Leak Detection Pump - DMTL (Diagnostic Module Tank Leakage) unit for the fuel tank evaporative emission (EVAP) system. The module sits between the...

Auxiliary Water Pump - electric coolant circulation pump for the fuel-fired booster heater circuit. The pump draws coolant through the fuel-burnin...

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Cylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...

Oil Drain Plug for the ZF transfer box housing. The plug closes the drain and fill port in the transfer box casing, and is removed to drain and re...

Electronic Pressure Control Solenoid for the transfer case control circuit. The solenoid is actuated electrically by the vehicle's control module ...

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...

Oil Separator Seal - sealing gasket for the oil separator in the crankcase ventilation system of the 2.7 and 3.0 litre V6 diesel engines. The oil ...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Camshaft Pulley Hub mounts to the front of the right-hand (RH) cylinder bank camshaft on the 2.7L and 3.0L V6 diesel engine, forming part of the ti...