Land Rover Discovery 5 Parts

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

o-ring oil cooler 3,0 TDV6

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Accessory Drive Idler Pulley

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Timing gear lower idler pulley for the engine timing drive system. This pulley guides and stabilizes the timing belt within the lower timing gear...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Brake Light Switch RR Sport 05-09 Disco3 05-09

Valve Body Adaptor - connects the valve block (main control) to the vacuum control valve on the ZF 6HP26 and 6HP28 six-speed automatic transmission...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Service PCV Kit

Stop light switch for the brake pedal box assembly. The switch mounts in the pedal box behind the brake pedal and is operated by the pedal arm as ...