Land Rover Discovery 5 Parts

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Starter Motor - the cranking motor of the engine electrical system, mounted at the engine-to-transmission bellhousing. Its pinion engages the flyw...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Stud

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Lithium-Ion Battery - the backup battery for the Telematics Control Unit (TCU). It supplies backup power to the telematics control unit so the uni...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Self-Tapping Screw and Washer - a 5 x 20mm self-tapping screw with a captive washer, used as a bumper and grille fixing. It secures the radiator g...

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Brake Caliper and Actuator - LH for the rear disc brake assembly, supplied complete with its electronic parking brake (EPB) actuator. The caliper h...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

EGT Sensor Exhaust gas temperature sensor in the exhaust and emissions aftertreatment system of the 3.0L V6 diesel engine. It measures exhaust gas...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Bolt

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Control Module Bracket for the adaptive cruise control distance sensor assembly. This mounting bracket secures the distance sensor to the vehicle ...

Ball Joint Separator - a heavy-duty scissor-type hand tool that eases tapered ball joints and track rod ends apart without impact, avoiding damage ...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...