Land Rover Discovery 5 Parts

Breather Tube for the crankcase ventilation system of the 3.0L supercharged V6 petrol engine. It routes crankcase blow-by gases from the engine as ...

Gasket - Turbocharger Cooling

Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...

Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...

Fixing Screw, M6 x 65 mm. A threaded fastener used as a general fixing across a range of vehicle assemblies.

Screw - M6 x 65mm threaded fastener. Factory-specified fixing screw with a 6mm (M6) thread and 65mm length.

Insulator - Bush Type

Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...

Cross Member Insulator for the rear suspension. This rubber mounting isolates the rear cross member from the body structure, damping road-induced ...

Crankcase Breather Tube for the crankcase ventilation system on the 3.0L V6 Supercharged Petrol. This tube routes crankcase blow-by gases from the...

Differential Mounting Washer used in the front differential mounting arrangement. The washer is fitted at a front differential mounting point, spr...

Anti-Roll Bar Bush - Front is the mounting bush that locates the front anti-roll (stabiliser) bar to the chassis cross member. It insulates and sec...

O-Ring seals a connection joint in the front air conditioning refrigerant circuit. It maintains the pressure-tight seal between refrigerant lines o...

Metal Name Plate is an exterior badge fitted to the bodywork. It mounts to the body panel as a model or trim identifier and forms part of the vehic...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Brake Fluid - DOT 4 low-viscosity hydraulic brake fluid, supplied in a 1 litre container. It transmits pedal pressure through the hydraulic brakin...

Magnetic Oil Drain Plug - M14 x 21 sump drain plug in the engine lubrication system. The plug seals the drain aperture in the oil sump and is remo...

Bolt is a chassis fastener securing the front and rear crossmember and stabiliser (anti-roll) bar mountings. Supplied individually.

Timing Chain Guide that locates and supports the timing chain along its run within the timing drive. It controls the chain path and reduces vibrat...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Coolant Hose carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It runs f...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Transfer Box Oil is the lubricant specified for the single-speed transfer case. It lubricates the transfer case internals and is used when carryin...

Drain Plug Sealing Washer seals the M18 oil drain and filler plug on the transfer case. The washer deforms as the plug is tightened to form a leak...

Anti-Roll Bar Link - connects the rear anti-roll (stabilizer) bar to the suspension on the left-hand side. This drop link transfers body-roll load...

Gasket - Throttle

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Hex Head Bolt and Washer - a hexagon-head bolt supplied with a washer. A general-purpose fixing used at multiple mounting locations, including the...

Cross Member Insulator - a rubber isolating bush fitted between the rear suspension crossmember and the body structure. It cushions the crossmembe...

O-Ring Kit - a set of eight O-ring seals for the heater and air-conditioning unit. The kit provides the sealing O-rings needed when servicing or r...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Upper Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the joint at the upper section of the two-piece inlet manifold, ma...