Land Rover Discovery 5 Parts

Diesel Exhaust Fluid (AdBlue) is a consumable fluid for the Selective Catalytic Reduction (SCR) exhaust aftertreatment system on diesel engines. I...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Interior Trim Retainer Clip - a moulded fastener used to secure interior trim to the vehicle body. The clip retains door casings, pillar trims and...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Fuel return tube O-ring seal

Lithium-Ion Battery - the backup battery for the Telematics Control Unit (TCU). It supplies backup power to the telematics control unit so the uni...

Key Fob Cover Kit is a replacement outer cover for the remote smart key. The kit contains the upper and lower cover halves with the function butto...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Water Outlet Connection for the engine cooling system, forming a coolant outlet from the engine. The connection provides the port and hose union t...

Wiper Relay is a 5-pin mini relay used in the wiper control circuit to switch the supply to the wiper motor. The five-pin layout provides a change...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Bolt

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Retaining Clip - a push-in trim retainer used to secure exterior mouldings and interior finisher panels. The nylon clip pushes into an 8 mm mounti...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Plain Washer - metric M10 flat washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Fuel Pump Drive Belt Kit for the 3.0L V6 diesel engine, renewing the belt that drives the high-pressure fuel pump at the rear of the engine. The k...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Starter Motor - the cranking motor of the engine electrical system, mounted at the engine-to-transmission bellhousing. Its pinion engages the flyw...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Transmission Oil Pan and Filter for the ZF 8HP 8-speed automatic transmission (8HP45 and 8HP70, and the later 8HP51/8HP76 variants). The pan bolts...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Primary Fuel Filter - the main in-line filter in the diesel fuel supply circuit, supplied complete with its mounting bracket. The filter is positi...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Oil Filter Element for the 3.0L AJ20 / AJ22 Ingenium six-cylinder engine, fitted in the engine lubrication circuit. The cartridge element seats in...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...