Land Rover Brake Shoes & Drums

Land Rover brake shoes cover three distinct systems: rear wheel drum shoes on Classic Defender models to approximately 1994 and all Freelander 1 variants; transmission handbrake shoes on the transfer box output shaft drum, which acts as the parking brake on Range Rover Classic, Discovery 1, Discovery 2, Range Rover P38, and all Classic Defenders across the full production run; and drum-in-hat parking brake shoes on Discovery 3, Discovery 4, Range Rover L322, Range Rover Sport L320, and early Freelander 2.

Sort by

View as

LR031947 - Brake Shoe Set - Axle Set

- €70,60

€70,60

€70,60 - €70,60

€70,60

OEM

Available to order: 2-3 weeks delivery

Brake Shoe Set - Axle Set

About This Category

About Land Rover Brake Shoes & Drums

Brake shoes are friction components that press against the inside of a rotating drum to generate braking or holding force. Across the Land Rover and Range Rover range they appear in three distinct systems, each requiring a different shoe type and specification.

Rear wheel drum shoes are the primary rear service brake on Series II and III, Series I, and all Freelander 1 variants. Early Classic Defender 90 and 110 models also used rear wheel drum shoes alongside front disc brakes, up to approximately chassis break in 1994. Series I through III run drum brakes at all four corners; the front and rear drums are different sizes and must be ordered separately.

Transmission handbrake shoes operate on a separate drum assembly mounted to the transfer box output shaft. This drum acts as the parking/handbrake mechanism on Range Rover Classic, Discovery 1, Discovery 2, and Range Rover P38. Importantly, all Classic Defenders also use a transfer box drum for the handbrake, regardless of whether the rear axle has drum or disc service brakes. The Range Rover Classic and Discovery 1 used all-round disc brakes as their primary service brakes throughout production; the only shoe they require is the transmission handbrake shoe.

Drum-in-hat parking brake shoes are a smaller, separate shoe set mounted inside the hub of a rear disc. These are used on Range Rover L322, Discovery 3, Discovery 4, Range Rover Sport L320, and early Freelander 2 models. On Discovery 3, Discovery 4, and Range Rover Sport L320, these shoes are operated electronically via an EPB actuator motor.

This collection also includes brake drums, return springs, adjusters, drum screws, and mud shields, as part of the Land Rover Brake System range.

Model Fitment

Brake Shoe Fitment by Model

Use the table below to confirm which shoe type applies to your vehicle. Several models require more than one shoe type; see the notes column.

Model	Years	Brake System	Shoe Type Required
Series I / II / IIA / III	1948 to 1985	Drum brakes all-round + transfer box drum	Wheel drum shoe (front and rear) + transmission handbrake shoe
Range Rover Classic	1970 to 1996	Disc brakes all-round + transfer box drum	Transmission handbrake shoe only (no rear wheel drum shoe)
Classic Defender (early)	1983 to ~1994	Front disc, rear drum + transfer box drum	Rear wheel drum shoe + transmission handbrake shoe
Classic Defender (late)	~1994 to 2016	Disc brakes all-round + transfer box drum	Transmission handbrake shoe only (rear uses disc pads)
Discovery 1	1989 to 1998	Disc brakes all-round + transfer box drum	Transmission handbrake shoe only (no rear wheel drum shoe)
Discovery 2	1998 to 2004	Disc brakes all-round + transfer box drum	Transmission handbrake shoe only (no rear wheel drum shoe)
Freelander 1	1997 to 2006	Front disc, rear drum	Rear wheel drum shoe (all variants and trim levels)
Range Rover P38	1994 to 2001	Disc brakes all-round + transfer box drum	Transmission handbrake shoe only
Range Rover L322	2002 to 2012	Disc brakes all-round + drum-in-hat parking brake	Parking brake shoe (drum-in-hat)
Discovery 3	2004 to 2009	Disc brakes all-round + EPB drum-in-hat	EPB handbrake shoe
Range Rover Sport L320	2005 to 2013	Disc brakes all-round + EPB drum-in-hat	EPB handbrake shoe
Discovery 4	2009 to 2016	Disc brakes all-round + EPB drum-in-hat	EPB handbrake shoe
Freelander 2 (pre-facelift)	2006 to ~2012	Disc brakes all-round + drum-in-hat parking brake	Parking brake shoe (drum-in-hat)
Freelander 2 (facelift)	~2013 onwards	Disc brakes all-round + motor-on-caliper EPB	No handbrake shoe fitted. EPB integrates into rear caliper piston.

EPB Service Mode Required

On Discovery 3, Discovery 4, and Range Rover Sport L320, the electronic parking brake actuator must be placed into service mode using a compatible diagnostic tool before the rear shoes can be retracted. Attempting to compress the actuator without activating service mode can damage the EPB actuator, cables, or parking brake system. This procedure is required every time the EPB shoes are replaced on these models.

Compatibility Guide

Selecting the Right Brake Shoe

Classic Defender (early, rear drum models): The transition from rear drums to rear discs occurred at approximately chassis number KA930455 / LA930456 in 1994. If you are unsure which your vehicle has, check the rear hub visually or use the chassis number to confirm. From the Td5 (1998) onwards, all Defenders used rear disc brakes. A transmission handbrake shoe set is still required on all Defenders regardless of rear axle brake type.

Series I through III: Front and rear drum sizes differ and must be ordered separately. Series wheel stud pattern and drum diameter vary by year, axle, and body style. Confirm the drum diameter from the old drum or your workshop manual before ordering. See the FAQ below for common Series drum part numbers.

Range Rover Classic and Discovery 1 / 2: These models use only a transmission handbrake shoe. Do not order rear wheel drum shoes for these vehicles. The transfer box drum is the sole shoe-type component required.

Freelander 2: The split between drum-in-hat and motor-on-caliper EPB occurred during the facelift production run at approximately 2012 to 2013. If your FL2 has a mechanical handbrake lever, it uses drum-in-hat shoes. If it has an EPB button and no cable-operated lever, it uses motor-on-caliper EPB and no handbrake shoes apply. Confirm by VIN before ordering.

Aftermarket brake friction components for road use in the EU should carry ECE Regulation 90 (ECE R90) approval, which confirms the friction material meets performance levels equivalent to the original equipment. Confirm ECE R90 compliance on the product listing when selecting aftermarket brake shoes for your Land Rover or Range Rover.

Fitting Notes

Always replace as an axle set. New shoes on one side and worn shoes on the other causes uneven braking force and can pull the vehicle under braking or reduce parking brake holding strength. Replace both sides at the same time using a matched pair from the same supplier and friction grade.
Replace springs and adjusters at the same time. Return springs weaken with heat cycling over time, and worn or corroded adjusters prevent the shoes from self-adjusting after bedding in. Springs, adjuster kits, and drum screws are stocked individually so the full hardware set can be renewed during a shoe replacement job.
Inspect the drum before refitting. Measure the drum diameter against the maximum wear limit stamped on the drum face or listed in the workshop manual. A worn, scored, or oval drum will destroy new shoes quickly and cannot be corrected by fitting new shoes alone.
Observe leading and trailing shoe orientation. On leading-trailing drum brake assemblies the two shoes differ in arc position. Fitting them reversed significantly reduces braking efficiency. Photograph or mark the original assembly before disassembly.
Keep linings free of oil and brake fluid. Contamination of the lining surface is not recoverable by cleaning. Before fitting new shoes, inspect the wheel cylinder or axle seal for leaks and address any source of contamination first.

Technical Guides

Electronic Parking Brake Failure

EPB fault diagnosis for Discovery 3, Discovery 4 and Range Rover Sport L320. Covers why worn handbrake shoes are a common root cause of actuator fault codes and how to diagnose correctly.

Land Rover EPB failure: diagnosis and repair

Discovery 4 Parking Brake Fault

Parking brake fault diagnosis and repair steps specific to Discovery 4, covering actuator, cable and shoe inspection.

Discovery 4 parking brake fault guide

Related Categories

Handbrake Parts

EPB actuators, handbrake cables, adjuster kits and handbrake hardware for Land Rover and Range Rover.

Land Rover handbrake and EPB parts

Brake Pads

Disc brake pads for Classic Defender, Discovery, Range Rover, Freelander and Range Rover Sport across all axles.

Land Rover brake pads

Brake Discs

Front and rear brake discs, solid and vented, for the full Land Rover and Range Rover model range.

Land Rover brake discs

Brake Hoses & Pipes

Flexible brake hoses and rigid brake pipe sets for Land Rover and Range Rover.

Land Rover brake hoses and pipes

Brake Kits & Servo Parts

Brake kits, axle sets, brake lining kits and servo vacuum pump components for Land Rover.

Land Rover brake kits and servo parts

Frequently Asked Questions

Brake Shoes & Drums FAQ

What types of brake shoe are used across the Land Rover range?

Brake shoes on Land Rover and Range Rover models fall into three types. Rear wheel drum shoes are the primary rear service brake on Series I through III (which also use front drums), early Classic Defender models to approximately 1994, and all Freelander 1 variants. Transmission handbrake shoes operate on a separate drum on the transfer box output shaft, acting as the parking brake on Range Rover Classic, Discovery 1, Discovery 2, Range Rover P38, and all Classic Defenders regardless of rear axle type. Drum-in-hat parking brake shoes are a smaller set mounted inside the rear disc hub, used on Discovery 3, Discovery 4, Range Rover L322, Range Rover Sport L320, and early Freelander 2 models to approximately 2012. The Freelander 2 facelift (approximately 2013 onwards) uses a motor-on-caliper EPB with no handbrake shoes at all.

Do brake shoes need to be replaced as a complete axle set?

Yes. Always replace brake shoes as a complete axle set. Replacing one side only causes uneven braking force, which can pull the vehicle to one side under braking or reduce parking brake holding strength. Axle sets covering both sides (for example STC2796 and STC2797 for certain Defender rear axles) are the most common format stocked. When removing the drum, also inspect the drum surface for scoring or ovality, the adjuster for wear or corrosion, and the wheel cylinder or EPB actuator seal for leaks before refitting.

Should I replace springs and adjusters when fitting new brake shoes?

Yes, this is strongly recommended. Return springs weaken over time with repeated heat cycling and worn or corroded adjusters prevent the shoes from self-adjusting correctly after bedding in, leading to a slack pedal or poor parking brake performance. Budget Parts stocks replacement springs, adjuster kits, and drum screws as individual components so the full hardware set can be replaced during a shoe job without ordering a full kit.

How do I know when handbrake shoes need replacing on a Discovery 3, Discovery 4 or Range Rover Sport L320?

Common signs include a handbrake warning light on the dashboard, an EPB fault code, or reduced holding force on a slope. On these models, the electronic parking brake actuator works harder as the shoes wear down and eventually triggers a fault. EPB faults that appear to indicate actuator failure are often caused by worn handbrake shoes. Replacing the actuator without addressing worn shoes typically leads to repeat failure within a short period. Worn handbrake shoes are the first item to inspect and replace when an EPB fault is diagnosed on these models.

Which brake drum fits my Series Land Rover?

Series drum sizes vary by year, axle position, and body style. For Series II, IIA and III rear axles, part number 591039 is the standard rear drum. For certain LWB Series II and IIA variants, 516599 applies. Early models with 10-inch drums use 591661. Front drums for Series models with a 2.6-litre or V8 engine and large-stud pattern are 576973 and 576974. The transmission handbrake drum for Series models is listed separately as SDC100200. Always check your wheel stud pattern and drum diameter before ordering, and use the part number from the old drum or your chassis number to confirm the correct fitment.

Technical content by the Budget Parts workshop team.