Land Rover Defender Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Dzus Fastener is a quarter-turn quick-release stud used to secure the radiator cowl and cooling fan shroud within the engine cooling assembly. The...

Plain Nut - an M10 threaded fastener used at engine and chassis fixing points. Applications include retaining the shock absorber mountings to the ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Fuel return tube O-ring seal

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Plain Washer - metric M10 flat washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Wheel Hub Assembly for the front and rear axle knuckle assembly. This wheel hub assembly mounts to the steering or rear knuckle and houses the whe...

Valve - Control

Accessory Drive Idler Pulley

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Water Connection for the turbocharger coolant feed, lower position, in the turbocharger lubrication and cooling circuit of the 3.0L AJ20P6 Ingenium...

Primary Fuel Filter - the main in-line filter in the diesel fuel supply circuit, supplied complete with its mounting bracket. The filter is positi...

Coolant Vent Hose - connects the engine vent elbow to the radiator, within the vent (bleed) circuit of the engine cooling system. The hose carries...

Crankcase cover gasket for the crankcase ventilation (emission control) cover on the 3.0L Ingenium six-cylinder petrol engine - AJ20P6 / AJ22P6, in...

Spark Plug - ignition spark plug for Ingenium petrol engines (AJ20 / AJ22 series, including PHEV applications). The plug screws into the cylinder ...

V-Belt for the front-end accessory drive of the 3.0L AJ20P6 six-cylinder petrol engine. The belt is driven by the crankshaft pulley and transmits ...

Coolant Expansion Tank Cap - pressure cap sealing the coolant expansion (overflow) container in the engine cooling circuit. The cap is a working c...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Relay - 20 A five-pin micro relay, black housing. A five-pin relay is a changeover type: a low-current control circuit energises the coil, which s...

Brake Pad Wear Sensor for the front axle, part of the brake pad wear warning circuit. The sensor is located in the brake pad and carries a wire lo...

Accessory Drive Belt for the front end accessory drive of the 2.0L Ingenium four-cylinder engine (AJ200 / AJ20P4, petrol and diesel applications). ...

Rear Upper Suspension Arm for the rear multi-link suspension assembly. The arm locates the upper end of the wheel carrier relative to the rear sub...

Cabin Pollen Filter for the front heating, ventilation and air conditioning intake housing. The element sits in the HVAC filter tray upstream of t...

Service PCV Kit

O-Ring

Coolant outlet tube forming the water outlet connection at the cylinder head, in the engine cooling circuit of the 2.0L I4 AJ200 Ingenium petrol en...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...