Land Rover Discovery Parts

Relay

Clevis pin

Clutch Release Lever Pivot Cap for the clutch release lever pivot pin. One is required per clutch release arm.

Flange Bolt - M10 x 35mm flanged hex bolt used at a range of driveline and engine mounting points, including bell housing, flywheel and clutch, tra...

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Poly-Vee Drive Belt for the Rover V8 petrol engine, in the specification fitted to vehicles equipped with ACE (Active Cornering Enhancement) and ai...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Rear Bumper Trim Retainer Clip for the Discovery 2 (L318). This plastic retainer clip secures the rear bumper finisher trim at the end-cap section...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Camshaft Sprocket for the 4.0L and 4.6L V8 petrol engine, part of the timing drive at the front of the engine. It is driven by the timing chain fr...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Wiper Arm Pivot Nut Secures the wiper arm to the splined pivot spindle of the windscreen wiper mechanism. It threads onto the spindle where it emer...

Bolt Threaded fastener used within the exhaust system assembly.

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Alternator Oil Feed Pipe supplies pressurised engine oil to the vacuum pump integrated at the rear of the alternator, on the Td5 2.5L 5-cylinder tu...

Front Brake Caliper Repair Kit for front calipers used with vented discs. The kit supplies the piston seals needed to overhaul the front calipers....

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Brake Master Cylinder - the hydraulic actuator at the head of the braking circuit, mounted to the brake servo. Force from the pedal, boosted by the...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

LHD Steering Drag Link Lemforder / Moog - Discovery 2

Drag Link Ball Joint (Short) is a steering linkage joint fitted at the short end of the drag link, within the steering track-rod circuit. It forms...

Polyvee Auxiliary Drive Belt, 1870 mm in length, running in the engine front-end auxiliary drive. Driven by the crankshaft pulley, the belt routes...

Turbocharger for the Td5 2.5L 5-cylinder turbo diesel engine. The turbocharger draws energy from the exhaust gas stream to drive a compressor whee...

Coolant Hose for the fuel cooler circuit in the engine cooling system. This hose routes coolant from the expansion tank to the fuel cooler rail, w...

Cooler Oil

Lower Radiator Hose - the bottom coolant hose in the engine cooling circuit of the 4.0L V8 petrol engine. It returns cooled coolant from the base ...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Bleed Hose is a small-bore coolant hose within the expansion tank and hose assembly of the engine cooling system. It connects the expansion tank t...

Oil Pressure Switch for the V8 petrol engine. The switch monitors oil pressure in the engine lubrication circuit and activates the instrument clus...

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Anti-Roll Bar Boot Kit is a rear actuator dust boot (gaiter) for the ACE (Active Cornering Enhancement) hydraulic anti-roll bar system. The boot s...

Intercooler Hose - the charge-air hose connecting the turbocharger to the intercooler on the Td5 2.5L 5-cylinder turbo diesel. It carries pressuri...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Bolt

Windscreen Finisher - the exterior trim moulding that finishes the upper edge of the front windscreen. Covers the top windscreen seal and the join...

ABS Sensor - Front for the wheel speed sensing circuit on the front axle. This is the short-type sensor, terminating directly in a connector. The ...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Drop Arm - Steering Box Output is installed on the steering box sector shaft within the power-assisted steering assembly. This component converts ...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Gearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...

Door Glass Channel for the side door glass assembly. The channel locates within the door frame and guides the window glass along its travel as it i...

Panhard Rod Bolt for securing the panhard rod to its axle bracket or chassis mount. This is a flanged hex bolt, M16 x 75mm. The integral flange di...