Land Rover Discovery Parts

Oil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...

Bulb and Holder for switch and control panel illumination. The orange-tinted bulb and its integral holder fit into the rear of dashboard switches ...

Stud - Turbo Outlet to Downpipe Flange in the exhaust system of the Td5 2.5L 5-cylinder turbo diesel engine. This stud secures the turbocharger ou...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Wheel Cylinder Brake - RH

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Automatic Transmission Shaft is a coupling shaft within the ZF 4-speed automatic gearbox assembly. This shaft transmits drive between internal gea...

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

D2 Brake caliper LH front

Brake caliper front RH D2

Synchromesh Ring - inner synchroniser ring for the R380 five-speed manual gearbox. Works within the mainshaft synchroniser assembly to bring the g...

Swivel Recovery Eye Rotating recovery point that bolts through the recovery-point holes in a winch bumper, providing a secure anchor for a shackle ...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Front Seat Armrest Finisher, the decorative trim panel forming the visible outer surface of the front seat armrest on the Discovery 2. Applies to ...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Floor Mat Set — moulded rubber floor mats for the front footwells, protecting the cabin floor and carpet. The tailored rubber mats sit in the driv...

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Flange Nut - M12 - an M12 fastener with an integral flanged face, used throughout the suspension assembly. The wide flange spreads the clamping lo...

Flanged Bolt - M10 x 92

Electronic Differential Lock (E-Locker) replaces the standard open differential assembly within the axle, providing driver-selectable full differen...

Flexible Brake Hose for the front right-hand side, part of the hydraulic braking circuit. The hose forms the flexible link between the rigid brake...

Wheel Spacer Set - 30mm - Black - a set of four black finished aluminium alloy spacers for 5x120 PCD hubs, fitted between the hub face and the whee...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

ACE High-Pressure Pipe - Rear Section within the Active Cornering Enhancement hydraulic circuit. This pipe forms the rear section of the high-pres...

Headlamp Levelling Motor for the front headlamp assembly. Electric actuator that adjusts the headlamp beam angle to compensate for vehicle load. M...

Valve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Poly Bush Set A front and rear set of polyurethane suspension bushes that replace the original rubber bushes on the chassis and suspension. Polyure...

Tow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...

Side Repeater Bulb Holder for the exterior indicator and side-repeater lighting circuit. The holder fits within the lens housing and provides the ...

Fuel Tank Cradle Support for the Discovery 2. This bracket forms part of the fuel tank cradle assembly, locating and supporting the fuel tank agai...

Adjustable Panhard Rod - Long - lateral axle locating link within the suspension assembly, supplied in the longer length variant. The Panhard rod ...

ACE Pipe – Pump to Valve Block (Front Half) for the Active Cornering Enhancement hydraulic circuit on TD5 diesel applications. This high-pressure p...

Shock Absorber Top Mount Bush for the front suspension – the rubber bush at the upper end of the front damper. The bush isolates the top of the fr...

Watts Linkage Bolt is an M14 fastener used in the rear suspension. It secures the Watts linkage to the rear axle, and is used in the same specific...

Road Coil Spring - Front for the Discovery 2 front suspension. This coil spring seats in the front spring pan on the axle beam and bears against t...

Coolant Hose for the engine cooling circuit, running between the radiator and the fuel cooler. On the 2.5L five-cylinder turbo-diesel (Td5), surplu...

Rear Step Assembly – Retractable, a folding step mounted at the rear body to give a low-height step for access to the load area and roof. It compr...

Gear Lever Gaiter Assembly - sealing gaiter for the manual gearbox gear lever. Fits around the base of the gear lever to seal the transmission tun...

Radiator Mounting - Rubber is a rubber isolation bush used to secure and cushion the radiator within its mounting points. It absorbs vibration and...