Land Rover Discovery Parts

Brake Caliper for the rear braking assembly, mounted on the right-hand side. The caliper houses the piston and hydraulic fluid inlet, converting p...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Air spring clip P38, D2

Spring plate

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

tank expansion, WITHOUT CAP!

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Plenum chamber hose

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Drain plug LT77 R380

Drive Belt Idler Pulley for the auxiliary (serpentine) drive belt system of the V8 petrol engine. The idler guides the belt and maintains its runni...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Rubber Mounting for the body-to-chassis mounting points. The rubber is fitted under the body mounting bolt, seated between the body and the chassis...

Selector yoke spherical bush

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Rear Brake Caliper Carrier for the rear disc brake assembly. The carrier bolts to the rear hub and holds the brake pads, locating the caliper over ...

Head gasket set 3.9 EFI MA on

Side Repeater Lens is the lens cover for the side repeater indicator lamp. It fits over the repeater lamp bulb to seal the unit and colour the emi...

Repair kit adjuster hand brake

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Oil seal

O-Ring seals the water rail (coolant rail) joint within the cooling system of the 4.0L and 4.6L V8 EFI petrol engine. Fitted at the water rail con...

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Ignition heater plug timer glow plug relay

Ignition Lead Set for V8 petrol engines, forming part of the ignition system. The set carries the high-tension spark from the ignition coil and di...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...