Land Rover Discovery Parts

Heater Blend Stepper Motor - Front is an electric actuator mounted on the heating and air-conditioning housing. It drives the air-blend flap that ...

Glove Box Door Damper. Controls the rate at which the glove box lid opens, providing a smooth, damped movement within the facia glove box assembly.

Brake Pads - Front - Less Springs - friction pads for the front axle, supplied as a complete axle set (one set per axle). The pads locate in the f...

Manifold Absolute Pressure (MAP) Sensor - measures the pressure inside the intake manifold and supplies an engine-load signal to the engine control...

Timing Belt Pulley, Upper from the upper timing gear, right-hand side. It guides the timing belt around the upper drive components and maintains c...

Roof Drip Rail Finisher is an exterior moulding that caps the roof drip rail. It runs along the roof-to-body joint, covering the drip channel to g...

O-Ring Seal for the cylinder head cover on the AJ-V8 4.4L petrol and 4.2L supercharged petrol engines. The seal locates in the groove of the cylin...

Bolt - M10 x 25 mm, with washer. Underbody and chassis fixing used to secure engine splash shields, heat shields and underbody protection panels t...

Bracket - Fender Mounting

Front heater hose for the passenger compartment heater coolant circuit. Carries coolant between the engine cooling system and the heater matrix, f...

Heater Manifold - the rigid coolant tube running from the engine block to the heater inlet hose on the 3.0L DOHC GDI supercharged V6 petrol engine,...

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Bracket - Mtg

Injector Refit Kit - Cylinders No.3 and No.4 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and...

Heater Blend Stepper Motor is an electric actuator mounted on the heating and air-conditioning housing. It drives an air-blend flap that regulates...

Turbocharger Adaptor Pipe in the induction system of the 2.5L 200 TDi and 300 TDi turbo diesel engines. It forms the connecting pipe between the t...

Coolant Overflow Tank for the engine cooling system, supplied with an integrated coolant level sensor. The tank is the pressurised expansion reser...

Fuel Filter Element for the 2.7L TDV6 diesel engine, fitted in the fuel supply circuit ahead of the high-pressure injection pump. The element remo...

Flame Trap, Crankcase Breather for the 3.5L V8 twin carburettor petrol engine. Fitted in the crankcase breather system of the carburettor V8, as l...

High-Mounted Stop Lamp - the centre high-mounted stop lamp (third brake light) mounted at the top of the rear of the vehicle. It illuminates with t...

Rear Brake Disc - 325 mm solid disc for the rear axle service brake assembly. The disc locates on the rear wheel hub flange and forms the friction...

Timing Chain Tensioner for the 2.0L Ingenium petrol engine (AJ200P). Maintains running tension on the timing chain, taking up slack to keep valve ...

Front Brake Hose - Left Hand - flexible hydraulic hose in the front brake circuit, running from the chassis-mounted rigid brake pipe to the left-ha...

Front Brake Hose - flexible hydraulic hose in the front brake circuit, running between the chassis-mounted rigid brake pipe and the front brake cal...

Rear Brake Hose - flexible hydraulic hose forming part of the rear brake hydraulic circuit. It carries pressurised brake fluid from the rigid brak...

Drive Belt Tensioner for the front accessory (auxiliary) drive of the 3.0L V6 diesel engine. It maintains correct tension on the drive belt that ru...

Body Mount Bracket - chassis-frame bracket forming part of the body mounting arrangement between the body and the chassis frame. The bracket is fi...

Differential Insulator - rubber mounting bush used in the differential mounting arrangement, on both the front axle case and the rear axle. It iso...

Lockable Retainer Handle for the detachable tow bar system. It secures and locks the removable tow bar neck into the receiver, and is supplied wit...

Injector Refit Kit - Cylinder No.1 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and pipes ass...

Climate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...

A-Pillar Drip Rail Moulding - left-hand exterior moulding running along the A-pillar, finished in satin black. Fitted along the upper edge of the ...

A-Pillar Drip Rail Moulding - right-hand exterior moulding running along the A-pillar, finished in satin black. Fitted along the upper edge of the...

Turbocharger Hose a flexible hose in the turbocharger induction circuit of the 2.5L TDi diesel engine. It carries pressurised charge air through t...

Floor Pan Blanking Plug. It closes an unused aperture in the floor pan, sealing the opening against water, dust and road debris.

Kit - Injector Refit

Throttle body heater plate for the 4.0L and 4.6L EFi Rover V8 petrol engine, fitted to the underside of the throttle body. The plate carries engin...

Transmission Mount Insulator locating the transmission mounting bracket. The rubber-to-metal insulator supports the transmission against the body ...

Coolant Hose, Expansion Tank to Thermostat from the engine cooling system pipes and hoses assembly. It links the base of the coolant expansion tank...