Land Rover Discovery Parts

Cam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...

Windscreen Washer Jet A heated twin-nozzle washer jet that directs washer fluid onto the windscreen. It seats into the scuttle or bonnet panel and ...

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Tappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...

Bolt Secures the radius arm to the axle bracket within the radius arms & links assembly. Installed through the radius arm bush and axle mounti...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

Pin - Split

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Pollen Filter for the heating and ventilation system. It installs in the cabin air intake, upstream of the blower motor, trapping dust, pollen and ...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Anti Roll Bar Link

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Tailgate Lock Actuator - Upper

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Sealing Strip is a windscreen glazing seal, supplied as a pair, forming part of the windscreen glazing assembly. The strips seal the windscreen gl...

Head Gasket - V8 - LH seals the left-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between ...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Clip retaining rear body mouldings to the body, including the rear wheel arch moulding and front door cladding. A push-in plastic clip; sold indiv...

HT Ignition Lead - No.7 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Cam Cover Gasket - Td5 - Late Type

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Door Handle Cover that caps the exterior door handle at the door lock control, finishing the handle assembly. Supplied in black, this is the blank...

Coolant Hose connecting the radiator to the expansion tank. Part of the engine cooling circuit, this hose links the radiator to the coolant expans...

Stud

Belt Tensioner Pulley for the auxiliary drive belt system on the 2.7L TDV6 Diesel engine. This pulley maintains correct tension on the auxiliary d...

Turbo Hose for the Td5 2.5L 5-cylinder turbo diesel induction system. Forms part of the air cleaner assembly, ducting filtered intake air from the...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

HT Ignition Lead - No.6 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Engine Mounting for the V8 petrol engine, forming part of the powertrain support system. It locates between the engine bracket and the chassis, ca...