Land Rover Discovery Parts

Expansion Tank Cap

EGR Outlet Pipe Gasket seals the joint between the EGR outlet pipe and the intake system on the 2.7L TDV6 diesel engine (Lion V6). It sits where r...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

EGR Unit for the exhaust gas recirculation system, mounted on the right-hand side and fed from the exhaust manifold. The exhaust gas recirculation...

Bush - Stabilizer Bar Link

Brake Pad Set for the rear axle disc brake assembly. The pads locate within the rear calipers and clamp against the rear discs, generating the fric...

Snap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Coolant Hose - the top radiator hose in the Td5 2.5L 5-cylinder turbo diesel engine cooling system. This hose forms part of the upper coolant circ...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Plug - Drain

Crankshaft Pulley Bolt for the Td5 2.5L five-cylinder turbo diesel engine, securing the crankshaft pulley and torsional vibration damper to the nos...

Brake Pad Wear Sensor - front brake pad wear warning wire, part of the front disc brake friction-monitoring circuit. The sensor wire clips into th...

Water Detector senses water that has collected in the fuel filter within the fuel filtration assembly. Diesel fuel carries water that the filter s...

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Handbrake Actuating Pawl Rod Actuating rod within the rear parking brake mechanism of the drum-in-disc handbrake assembly. It transmits handbrake ...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Clamp - Tube

Rear Mudflap Kit mounts at the rear of the vehicle to reduce road spray and protect the lower bodywork and rear window from mud and debris. Intend...

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Leak-Off Tube - Injection Pump

Propeller Shaft - the rear propshaft that transmits drive from the transfer box output to the rear axle differential. It carries torque along the ...

Wheel Hub and Bearing is a front wheel hub assembly with an integrated wheel bearing, operating within the front knuckle and hub group. The unit m...

Washer used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...

Flange Nut, M16 for the suspension arm mountings. The integral flange spreads the clamping load over a wider bearing area and removes the need for...

4

Transmission Oil Pan - fluid pan for the ZF 6HP26 / 6HP28 six-speed automatic transmission, forming the base of the transmission casing and holding...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Fuel Tank for Discovery 3, Discovery 4, and Range Rover Sport equipped with the 10MY-specification tank (two vent pipes). This is the complete fue...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Oil Separator is part of the crankcase ventilation system on the 2.7L V6 Lion diesel engine. It separates oil mist from the crankcase blow-by gase...

Exhaust Gas Temperature Sensor measures exhaust gas temperature at the front of the diesel particulate filter, in the upstream section of the after...

Hose

Intercooler Air Duct forms part of the intercooler air duct and hose assembly on the charge air side of the induction system. It routes air betwee...

EGR Gasket for the 2.7L TDV6 diesel engine (140kW). This gasket seals the Exhaust Gas Recirculation (EGR) system connections in the engine, preven...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Rear Lamp Assembly - Discovery 2 - RH

Rear Bumper Bracket Clip - a plastic retaining clip used in the rear bumper assembly to secure the bumper bracket to the body. It locates the brac...