Land Rover Discovery Parts

Layshaft is the countershaft within the R380 five-speed manual gearbox, carrying the cluster of gears that mesh with the mainshaft gears. Drive pa...

Roof Gasket seals the joint between the roof panel and the body structure on the Discovery 1. The gasket runs around the roof panel perimeter, pre...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Locking Washer

Bulb & Holder - Main Instrument Panel for the Discovery 2 instrument cluster illumination circuit. This bulb and holder assembly fits into the...

Gearbox Selector Circlip - a retaining circlip within the manual transmission gear selector mechanism. The circlip locates on its shaft to secure ...

Grille Grommet - a mounting grommet for the front grille and headlamp surround panel. It seats in the body panel to receive and retain the grille ...

Screw - M6 metric fixing screw, 30 mm long. A general-purpose threaded fastener used to secure body panels, door-frame fittings and other bolted a...

Fastener used to secure interior door casing panels and body side trim. Retains door casing and rear body panel trim on applicable vehicles.

Housing thermostat GENUINE ROVER

Primary Fuel Filter for the diesel fuel supply system of the 2.0L I4 diesel (AJ200 / AJ20D4 / AJ21D4) engine. The primary filter separates water a...

Front Brake Pipe - Right-Hand - short rigid steel brake pipe forming the secondary link between the chassis-mounted flexible hose and the front rig...

Heater Hose - Coolant Valve is a moulded coolant hose in the heater circuit of the engine cooling system. It connects the heater control (coolant)...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Cap Reservoir Br.m.cylinder

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Spring Clip - Steel for V8 EFI petrol engines, used in the throttle linkage and gear change mechanism. This steel spring clip provides positive re...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Camshaft Washer is a retaining washer used at the front of the camshaft within the timing drive of the 3.5L V8 petrol engine. It is fitted at the ...

Washer 577254

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Locking Wheel Nut Cap in stainless steel, fitting over the exposed end of a locking (anti-theft) road wheel nut. The cap conceals and protects the...

Spare Wheel Cover for Discovery 1 and Discovery 2, sized to fit a 255mm-wide tyre on a 16- or 18-inch wheel. The cover has a rigid backing panel a...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Hex Nut

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Grille is the front-face grille panel for the Discovery 1, fitted to the nose of the vehicle between the headlamps and above the front bumper. Thi...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

U-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

J Bolt for the battery mounting assembly. The J-shaped threaded bolt hooks through the battery mounting bracket. The threaded end accepts a nut to...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Wastegate Control Hose for the 2.5L 200 TDi turbo diesel engine. This hose forms part of the turbocharger boost-control circuit. It routes the boo...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Front Seat Armrest Finisher, the decorative trim panel forming the visible outer surface of the front seat armrest on the Discovery 2. Applies to ...

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...