Land Rover Discovery Parts

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

oil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

screw M5 x 12

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Fuel Filter for the diesel fuel supply system of the 2.2L DW12 common-rail direct-injection turbo diesel engine. It is fitted in the fuel line betw...

Air Filter Element for the engine air intake system, seated within the air cleaner housing. The element traps dust and airborne particles from the...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Diesel Exhaust Fluid (AdBlue) is a consumable fluid for the Selective Catalytic Reduction (SCR) exhaust aftertreatment system on diesel engines. I...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Crankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Starter Motor - Defender TD4

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

pad foam OEM, eneregy absorbing. (Bij filter LR111341)

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Sump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Brake Pad Set for the rear axle disc brake assembly. The friction pads locate within the rear caliper and are clamped against the brake disc to ge...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Exhaust Gas Pressure Sensor for the diesel particulate filter (DPF) circuit on the 2.0L I4 AJ200D diesel engine. The sensor measures exhaust gas p...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Cylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...

Exhaust Gas Pressure Sensor mounted in the front pipe / catalyst section of the exhaust system. The sensor measures exhaust gas pressure and repor...

Bolt used in the front brake disc and caliper assembly. This is a securing fastener within the front braking installation.

Front Brake Pad Wear Sensor monitors friction-material thickness at the front axle. As the brake pads approach their wear limit, the sensor circuit...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Emission Gasket for the crankcase cover, part of the crankcase ventilation and emission-control system on the 2.0L AJ200/AJ20D4 four-cylinder diese...

O-Ring sealing the variable valve timing (VVT) solenoid cover. Seals the VVT solenoid cover within the engine timing gear, preventing oil leakage ...

Guide - Timing Chain

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...