Land Rover Fuel System Parts

Injector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Air Intake Grille for the cold air induction system. This adaptor grille sits at the cold air intake, drawing cooler outside air into the intake d...

Sealing Washer for the fuel injector, part of the diesel fuel injection system. The washer seats between the base of the injector and its bore in ...

Engine Stop Cable is the manual control cable that shuts down the 2.25L diesel engine by pulling the fuel injection pump stop lever to the no-fuel ...

Injector O-Ring seals the fuel injector within the fuel injection system of the 2.4L Duratorq TDCi (Puma) diesel engine. The seal maintains a pres...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Injector Nozzle is the atomising tip of the diesel fuel injector, sitting in the fuel injection circuit between the injector body and the combustio...

Throttle Body Gasket seals the throttle body to the plenum chamber on the 4.0L and 4.6L V8 EFI petrol engine. Fitted between the throttle body and...

Air cleaner to carburettor hose

Filler pipe hose 90

Fuel Tank Gauge is the fuel level sender unit in the fuel tank assembly. A float-operated sender mounted in the tank, it varies its electrical res...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Fuel Tank Sender Unit for the petrol fuel level sensing circuit. The sender uses a float arm connected to a variable resistor to measure the fuel ...

Banjo Bolt for the fuel and oil circuits, used to secure a banjo union to its housing while allowing fluid to pass through the cross-drilled body. ...

Choke Cable for the carburettor cold-start circuit, connecting the dashboard-mounted choke control to the carburettor choke linkage. When pulled, ...

Bolt - a hexagonal-head bolt with a 1/4" UNF (Unified Fine) imperial thread and a 1-1/4" length. Used as a body and chassis fixing at points such a...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Accelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...

Fuel Cooler for the diesel fuel return circuit. Mounted in the return line between the fuel injection system and the tank, it dissipates heat pick...

Fuel Tank with integral skid guard for the fuel storage system. The pressed-steel tank incorporates a welded underside skid guard that shields it ...

Regulator Pressure Fuel 3.5V8 - EFI

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Fuel Tank Cradle from the rear fuel tank mounting - the steel support frame that carries the classic-pattern plastic fuel tank beneath the chassis....

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Fuel Tank for the V8 EFI petrol fuel storage system. This multi-vent tank assembly holds the vehicle's petrol supply and feeds the fuel delivery ci...

Fuel Tank Bracket for securing the fuel tank to the vehicle chassis. This metal bracket forms part of the fuel tank mounting assembly, locating an...

Injector Pipe - No.4 is a high-pressure fuel line in the injection system of the 2.5L 4-cylinder diesel engine. It forms part of the set of rigid ...

Injector Pipe - No.3 for 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. This high-pressure steel fuel pipe routes fuel from the me...

Injector Pipe - No.2 for 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. This high-pressure steel fuel pipe routes fuel from the me...

Injector Pipe - No.1 for 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. This high-pressure steel fuel pipe routes fuel from the me...

Fuel Pump & Sender Unit - the in-tank fuel delivery module for petrol V8 EFI applications, combining the electric fuel pump and the fuel-level ...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Banjo Bolt

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

Rear Fuel Tank Assembly is the main fuel storage vessel of the fuel system, mounted at the rear of the vehicle. It holds the fuel supply and feeds...

Filter Kit - 2.2 & 2.4 TDCi for the Land Rover Defender with the Puma TDCi diesel engine. This kit consolidates the main filter and sealing it...

Fuel Return Hose forms part of the fuel return line on the 2.2L Puma TDCi diesel engine. It carries surplus fuel from the injection system back to...

Fuel Filler Hose connecting the external fuel filler neck to the fuel tank on the Defender. This rubber hose forms the sealed connection between t...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

In-Tank Fuel Pump & Sender Unit for Range Rover P38A petrol applications. This combined assembly houses the electric fuel pump and fuel level s...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Fuel Spill Pipe for the 200 TDi diesel injection system, part of the injector leak-off (spill return) circuit. The pipe links the injector leak-of...

Fuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...

Gasket kit carburettor Zenith Stromberg 175CD