Land Rover Gearbox & Transferbox Parts

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Transfer Box Sealing Washer for gearbox and transfer box drain and filler plugs. This sealing washer fits beneath the drain or filler plug thread,...

Transfer Box Sump Gasket for the LT76 combined gearbox and transfer box unit used in Series Land Rovers. This flat sealing washer seals the transf...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Plain Nut - 1/4" BSF hexagonal plain nut in the British Standard Fine (BSF) thread form. The BSF thread form uses a finer pitch than BSW (British ...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Speedometer Pinion Oil Seal for the gearbox speedometer drive take-off. It seals around the speedometer drive pinion where it enters the gearbox ho...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Gasket

O-Ring - seal for the LT76 manual gearbox, seated within the transmission assembly to seal a mating joint against oil leakage. Early-type ring, fi...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Sealing ring

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Selector Rod Rubber Grommet Washer is the rubber sealing element fitted around the reverse gear selector shaft at its exit point through the Series...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Transfer Lever Knob in yellow, for the four-wheel-drive engagement lever on the transfer gearbox. It threads onto the top of the selector lever an...

Spring plate

Gear Lever is the main gearbox selector lever. It mounts into the gearbox remote housing and is moved by the driver to engage the forward gears and...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Joint Washer seals the gearchange/inspection cover against the transfer box casing within the transfer gearbox assembly. Fitted between the cover ...

Mainshaft Nut for the LT76 gearbox, fitted to the mainshaft and gear assembly. It retains the gear cluster on the mainshaft, clamping the stack ag...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Gearbox Gasket for the LT67 manual gearbox. The gasket seals a mating joint on the gearbox casing, maintaining the oil seal between components and...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Mounting Rubber is a round rubber isolator that supports the powertrain on its chassis crossmember. It serves as the rear engine block mounting an...

Layshaft Bearing for the Series manual gearbox. It supports the layshaft (countershaft) within the gearbox casing, allowing the constant-mesh gear ...

Gearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Gearbox Front Layshaft Bearing for the LT76 main gearbox, supporting the front end of the layshaft (cluster gear) within the gearbox casing. It ca...