for Discounts / VAT
for Discounts & Correct VAT
Gearbox and transfer box parts for Land Rover and Range Rover, covering ZF automatic units, manual gearboxes, transfer cases, and the seals, bearings, and fluids that keep them running. Stocked across our Dutch warehouse network for EU dispatch, with brands including SKF, Corteco, and Timken.
Needle Roller Bearing - LT95
Automatic Transmission Oil Pump for the 4-speed automatic gearbox, part of the transmission's internal hydraulic system. The pump sits at the fron...
View full detailsTransmission Oil Cooler Hose - Diesel ZF Automatic is a hydraulic hose forming part of the automatic transmission cooling circuit on the Range Rove...
View full detailsVacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...
View full detailsScrew - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...
View full detailsDrain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...
View full detailsDowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...
View full detailsSealing Washer - sump plug sealing washer for the ZF four-speed automatic gearbox. Fitted under the head of the transmission sump drain plug, the ...
View full detailsCoupling Shaft Repair Kit for the MT82 six-speed manual gearbox, servicing the coupling flange and input shaft that transmit drive from the gearbox...
View full detailsDistance Piece for the LT76 gearbox mainshaft. This spacer maintains the correct axial position of components along the mainshaft within the LT76 ...
View full detailsCountersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...
View full details1st Speed Gear - first-gear wheel for the LT76 four-speed gearbox. It forms part of the gearbox gear train, meshing with the layshaft to provide t...
View full detailsThrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...
View full detailsTransmission Sealing Ring for the ZF 5-speed automatic transmission. It seals the fluid filter to the transmission and is renewed with the filter d...
View full detailsSynchromesh Ring - inner synchroniser ring for the R380 five-speed manual gearbox. Works within the mainshaft synchroniser assembly to bring the g...
View full detailsSynchro Ring - 5th Gear - R380 is the baulk ring for the 5th gear synchromesh assembly in the R380 5-speed manual gearbox. The ring equalises the ...
View full detailsSynchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...
View full detailsGearbox Crossmember for the chassis of long wheelbase Series Land Rovers. This steel crossmember spans the chassis rails beneath the gearbox, prov...
View full detailsOutput Shaft Oil Seal for the MT82 6-speed manual gearbox. Seals the output shaft at the rear of the transmission casing, preventing oil loss towar...
View full detailsThrust Washer 1.45mm Diff - LT230
Speedometer Drive Gear sits on the output shaft of the LT230 transfer box and forms part of the speedometer drive, transmitting shaft rotation to t...
View full detailsDrive Meter Speedo Gear Yellow 22 Teeth
Layshaft Nut for the R380 five-speed manual gearbox. It secures the layshaft gear cluster on its shaft, torqued to specification and then staked in...
View full detailsPrimary Pinion Shim - 2.00 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...
View full detailsSpring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...
View full detailsIntermediate Shaft
Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...
View full detailsStud for use in Land Rover gearbox assembly.
Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...
View full detailsAutomatic Transmission Dipstick, 4-Cyl Tdi
Transfer Box Gear Set - High Ratio is a gear set for the two-speed transfer box that raises the high-range gearing. By raising the high-range rati...
View full detailsRear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...
View full detailsTransmission & Power Steering Fluid
Valve Body Adaptor - connects the valve block (main control) to the vacuum control valve on the ZF 6HP26 and 6HP28 six-speed automatic transmission...
View full detailsDifferential Oil Seal for the final drive of the Jatco five-speed automatic transmission. It seals the differential output where the driveshaft pa...
View full detailsAutomatic Transmission Fluid for the JF506E five-speed automatic transmission. Supplied in a 1 litre container. The fluid meets the JF506E specifi...
View full detailsTorque Converter Oil Seal seals the front of the ZF 9HP nine-speed automatic transmission where the torque converter hub enters the pump housing. I...
View full detailsLower Engine Mount for the 2.0L four-cylinder turbocharged petrol engine. The mount (lower insulator) supports the engine and isolates engine vibr...
View full detailsTorque Converter Seal Kit - ZF 8-Speed
Auxiliary Battery, wet non-spillable type, providing backup power to the automatic transmission gear change assembly. Used with the AWF21 6-speed ...
View full detailsTransmission Oil, SAE 75W, meeting specification BOT 352, supplied in a 1 L bottle. For the 6-speed manual transmission (M66) and, on hybrid appli...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsOil - Auto Trans 4L
Output Shaft Oil Seal seals the transmission output shaft where it exits the case on the ZF 9HP48 / 9HP50 nine-speed automatic gearbox. It runs aga...
View full detailsTransmission Oil 75W-90 - a 75W-90 gear oil for manual transmission and driveline applications. Formulated to a multivehicle specification for use...
View full detailsTransmission Oil Drain Plug for the ZF 6HP26 and 6HP28 six-speed automatic transmission - Transmission External Components assembly group. M18 x 1...
View full detailsTransmission Extension Housing is the rear transmission mounting that supports the gearbox on the crossmember, incorporating a bonded rubber insula...
View full detailsCategory Overview
Every Land Rover and Range Rover uses a two-part driveline: a main gearbox that handles gear ratios and torque delivery, and a transfer box that splits drive between the front and rear axles for the brand's 4x4 traction. Both are serviceable assemblies and both are made up of parts that wear, leak, or fail individually long before the unit itself needs replacing. This collection covers the seals, bearings, synchros, gaskets, fluids, and rebuild components for the gearboxes and transfer cases fitted across the Defender, Discovery, Range Rover, Freelander, and Series ranges.
For most owners the right approach is component replacement, not unit replacement. A leaking output seal, a worn bearing, or contaminated fluid are repairable faults. Knowing which fault you have, and which part fits your specific gearbox or transfer case, is the difference between a straightforward fix and an expensive misdiagnosis.
ZF Automatic GearboxesModern Land Rover and Range Rover models run almost exclusively on ZF automatic transmissions. The ZF 6HP26 sits in the Range Rover L322, Range Rover Sport L320, and Discovery 3 and 4. The ZF 8HP series followed it across the Range Rover L405, Range Rover Sport L494, Range Rover L460, Range Rover Sport L461, and Discovery 5.
These gearboxes are precision hydraulic-mechatronic units. The valve body, torque converter, and electronic control module are the most common failure points, usually triggered by degraded fluid rather than mechanical wear. Symptoms such as delayed engagement, gear hunting, or harsh shifting on a warm gearbox typically point to valve body or fluid condition, not to a failing transmission.
For service work on these units, ZF specifies ZF Lifeguard Fluid 6 (6HP series) or ZF Lifeguard Fluid 8 (8HP series). The two fluids are not interchangeable. ZF's official position on 8HP service intervals is "fill for life", but independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km on vehicles used for towing, urban driving, or high-mileage motorway work. For the technical detail on fluid specifications and service requirements, ZF Aftermarket publishes its own transmission oil reference guide.
Confirm the ZF gearbox code on your vehicle before ordering fluid or service kits. ZF Lifeguard Fluid 6 and Lifeguard Fluid 8 are different specifications, and using the wrong grade is the most common cause of valve body wear after a DIY service.
Manual gearboxes are less common on current production but are still the dominant powertrain across the Classic Defender, early Discovery, Freelander 1, and the Series range. The R380 was the long-running five-speed unit fitted to the Discovery 1 (post-200Tdi production), Discovery 2, and Classic Defender from the 300Tdi through to early Td5. The MT82 six-speed replaced it on the Defender 2.4 and 2.2 TDCi Puma. Earlier production used the LT77 (Discovery 1 200Tdi era) and the LT76 and LT95 on Series 2/3 vehicles.
These units fail in predictable ways. Synchroniser rings on second and third gear wear first. Input shaft and lay shaft bearings degrade with age and oil contamination. Selector linkages and detent springs cause the symptoms most often misdiagnosed as a gearbox fault. Reverse idler gear chatter is common on R380 units past 240,000 km.
For most manual-gearbox owners, parts-level repair is straightforward and rebuild kits are available for the R380, LT77, and MT82. Specific Freelander 1 parts (IB5 manual) sit under the Freelander 1 collection. Series 2/3 gearbox parts have their own fitment requirements covered under the Series 2 and 3 collection.
Transfer BoxesThe transfer box carries as much load as the gearbox and is often the part that goes ignored until it fails. The LT230 is the dominant transfer case across the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and P38. It uses gear-drive between input and output shafts and a chain-drive system to the front output. The Discovery 3 and Discovery 4 use a chain-drive Magna Steyr unit with an electronic shift system. Modern Range Rover and Range Rover Sport models on the L405, L494, L460, and L461 platforms use a ZF-integrated transfer case as part of the transmission assembly.
Common failures are output shaft seal leaks, chain stretch on chain-drive units (Magna Steyr and modern ZF), viscous coupling failure on units fitted to early Discovery 2 and Range Rover P38, and selector motor failure on electronic-shift cases.
Transfer box fluid is not the same specification as gearbox fluid on most Land Rover and Range Rover units. The LT230 takes EP90 (or the Land Rover-specified MTF94 on later units), and the Magna Steyr unit on Discovery 3 and 4 takes a specific ATF spec. Confirm before ordering.
Most gearbox parts returns are caused by ordering errors at the buying stage rather than parts faults. The following are the most common we see across the Land Rover and Range Rover range.
For parts that overlap with the clutch system on manual gearboxes, see the Land Rover clutch parts collection. For driveline parts forward and aft of the gearbox, see the driveshaft and propshaft parts collection.
Technical GuidesIn-depth diagnostic and component guides for the gearbox-adjacent failure modes that come up most often on Land Rover and Range Rover models.
Technical breakdown of the L494's 3.0 TDV6 timing chain issues, air suspension faults, and ZF 8HP wear patterns. Covers what fails, why it fails, and which parts the workshop will need.
Range Rover Sport L494 ZF 8HP guideHow to tell drivetrain noise apart from gearbox or transfer box noise, and which parts to inspect before ordering. Covers Discovery 4, Freelander 2, and Series 3 driveline symptoms.
Land Rover driveline diagnosis guideClutch faults are routinely misdiagnosed as gearbox faults due to overlapping symptoms. This guide explains how to identify the real fault before replacing parts.
Land Rover clutch diagnosis guideThe gearbox controls gear ratios and torque delivery from the engine; the transfer box splits drive between the front and rear axles for 4x4 traction and also provides the low-range gearing on Defender and Discovery models. Both are serviceable assemblies and both fail in distinct ways. Drivetrain symptoms can come from either, which is why most Land Rover gearbox parts returns are caused by mis-diagnosis rather than mis-fit.
ZF 6HP26 transmissions (fitted to Range Rover L322, Range Rover Sport L320, Discovery 3, and Discovery 4) take ZF Lifeguard Fluid 6. ZF 8HP transmissions (fitted to Range Rover L405, L460, Range Rover Sport L494 and L461, and Discovery 5) take ZF Lifeguard Fluid 8. The two fluids are not interchangeable. Confirm the gearbox code stamped on the casing before ordering.
ZF's official position on the 8HP series is fill-for-life. In practice, independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km, particularly on vehicles used for towing, frequent urban driving, or high-mileage motorway work. The 6HP26 typically receives a service interval at 90,000 km. Manual gearboxes (R380, MT82, LT77) take a gear oil change at approximately 60,000 km.
The LT230, fitted to the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and Range Rover P38, fails in three main ways: output shaft seal leaks (often caused by flange wear behind the seal), input gear bearing wear, and selector linkage faults that mimic gearbox symptoms. Most LT230 issues are repairable with component-level parts rather than a full transfer case replacement.
The R380 five-speed manual was fitted to the Discovery 1 (post-200Tdi), Discovery 2, and Classic Defender from the 300Tdi era through to early Td5 production. The LT77 preceded the R380 on the Discovery 1 200Tdi. The MT82 six-speed replaced the R380 on the Defender 2.4 and 2.2 TDCi Puma. Rebuild kits and individual components for all three are stocked in this collection.
Yes. Most Land Rover transmission service jobs touch both units, particularly fluid changes, seal replacements, and bearing kits. Ordering both at the same time reduces vehicle downtime and is the most common workshop order pattern.