for Discounts / VAT
for Discounts & Correct VAT
Gearbox and transfer box parts for Land Rover and Range Rover, covering ZF automatic units, manual gearboxes, transfer cases, and the seals, bearings, and fluids that keep them running. Stocked across our Dutch warehouse network for EU dispatch, with brands including SKF, Corteco, and Timken.
Oil Temperature Sender for the engine oil temperature gauge circuit. The sender threads into the oil gallery and carries a temperature-sensitive re...
View full detailsSealing Plug for the transmission handbrake drum on the LT95 four-speed gearbox. The drum-type transmission handbrake acts on the transfer box out...
View full detailsGear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...
View full detailslock washer. sold EACH.
Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...
View full detailsO-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...
View full detailsOil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...
View full detailsGearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...
View full detailsGearbox Top Cover Plate - the cover plate that closes the top aperture of the main gearbox casing. It seals the top of the gearbox over the select...
View full detailsThrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...
View full detailsGear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...
View full detailsBellhousing Grommet is the rubber grommet that seals an aperture in the clutch bellhousing. It closes the opening in the bellhousing casing to kee...
View full detailsGear Lever for the main gearbox, right-hand drive configuration. The gear lever is the primary driver interface in the gearbox change mechanism, t...
View full detailsClutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...
View full detailsReverse lamp switch LT85 V8
Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...
View full detailsGearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...
View full detailsBolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...
View full detailsGearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...
View full detailsBolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...
View full detailsCirclip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...
View full detailsBolt - 5/16" UNF x 3-3/4" A 5/16" UNF setbolt, 3-3/4" long, catalogued for use across several applications. Its uses include securing the timing/f...
View full detailsGearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...
View full detailsLock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...
View full detailsMainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...
View full detailsWasher Thrust 3rd Gear
Distance sleeve mainshaft
Gearbox Thrust Washer
Mainshaft peg
Spring pin
Bronze Distance Piece Mainshaft 1954-71
Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...
View full detailsScrew
Engine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...
View full detailsLayshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...
View full detailsFiller and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...
View full detailsPTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...
View full detailsSnap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...
View full detailsThrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...
View full detailsThrust Washer - 0.130" A gearbox mainshaft thrust washer for the second-speed gear, 0.130" thick. It controls the end-float of the 2nd-speed gear ...
View full details2nd Speed Gear (29 teeth) for the mainshaft in the Series-type manual gearbox (LT76), from suffix D onwards. This gear meshes with its correspondi...
View full detailsGearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...
View full detailsGear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...
View full detailsAutomatic Transmission Sump Plug Sealing Washer in aluminium. This sealing washer fits between the sump plug and the valve block mating face, prov...
View full detailsLayshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...
View full detailsDistance bush mainshaft
Plate
Reverse Selector Fork for the gear selection mechanism in the Series-type manual gearbox (LT76), suffix B onwards. Mounted on the selector shaft, ...
View full detailsCategory Overview
Every Land Rover and Range Rover uses a two-part driveline: a main gearbox that handles gear ratios and torque delivery, and a transfer box that splits drive between the front and rear axles for the brand's 4x4 traction. Both are serviceable assemblies and both are made up of parts that wear, leak, or fail individually long before the unit itself needs replacing. This collection covers the seals, bearings, synchros, gaskets, fluids, and rebuild components for the gearboxes and transfer cases fitted across the Defender, Discovery, Range Rover, Freelander, and Series ranges.
For most owners the right approach is component replacement, not unit replacement. A leaking output seal, a worn bearing, or contaminated fluid are repairable faults. Knowing which fault you have, and which part fits your specific gearbox or transfer case, is the difference between a straightforward fix and an expensive misdiagnosis.
ZF Automatic GearboxesModern Land Rover and Range Rover models run almost exclusively on ZF automatic transmissions. The ZF 6HP26 sits in the Range Rover L322, Range Rover Sport L320, and Discovery 3 and 4. The ZF 8HP series followed it across the Range Rover L405, Range Rover Sport L494, Range Rover L460, Range Rover Sport L461, and Discovery 5.
These gearboxes are precision hydraulic-mechatronic units. The valve body, torque converter, and electronic control module are the most common failure points, usually triggered by degraded fluid rather than mechanical wear. Symptoms such as delayed engagement, gear hunting, or harsh shifting on a warm gearbox typically point to valve body or fluid condition, not to a failing transmission.
For service work on these units, ZF specifies ZF Lifeguard Fluid 6 (6HP series) or ZF Lifeguard Fluid 8 (8HP series). The two fluids are not interchangeable. ZF's official position on 8HP service intervals is "fill for life", but independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km on vehicles used for towing, urban driving, or high-mileage motorway work. For the technical detail on fluid specifications and service requirements, ZF Aftermarket publishes its own transmission oil reference guide.
Confirm the ZF gearbox code on your vehicle before ordering fluid or service kits. ZF Lifeguard Fluid 6 and Lifeguard Fluid 8 are different specifications, and using the wrong grade is the most common cause of valve body wear after a DIY service.
Manual gearboxes are less common on current production but are still the dominant powertrain across the Classic Defender, early Discovery, Freelander 1, and the Series range. The R380 was the long-running five-speed unit fitted to the Discovery 1 (post-200Tdi production), Discovery 2, and Classic Defender from the 300Tdi through to early Td5. The MT82 six-speed replaced it on the Defender 2.4 and 2.2 TDCi Puma. Earlier production used the LT77 (Discovery 1 200Tdi era) and the LT76 and LT95 on Series 2/3 vehicles.
These units fail in predictable ways. Synchroniser rings on second and third gear wear first. Input shaft and lay shaft bearings degrade with age and oil contamination. Selector linkages and detent springs cause the symptoms most often misdiagnosed as a gearbox fault. Reverse idler gear chatter is common on R380 units past 240,000 km.
For most manual-gearbox owners, parts-level repair is straightforward and rebuild kits are available for the R380, LT77, and MT82. Specific Freelander 1 parts (IB5 manual) sit under the Freelander 1 collection. Series 2/3 gearbox parts have their own fitment requirements covered under the Series 2 and 3 collection.
Transfer BoxesThe transfer box carries as much load as the gearbox and is often the part that goes ignored until it fails. The LT230 is the dominant transfer case across the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and P38. It uses gear-drive between input and output shafts and a chain-drive system to the front output. The Discovery 3 and Discovery 4 use a chain-drive Magna Steyr unit with an electronic shift system. Modern Range Rover and Range Rover Sport models on the L405, L494, L460, and L461 platforms use a ZF-integrated transfer case as part of the transmission assembly.
Common failures are output shaft seal leaks, chain stretch on chain-drive units (Magna Steyr and modern ZF), viscous coupling failure on units fitted to early Discovery 2 and Range Rover P38, and selector motor failure on electronic-shift cases.
Transfer box fluid is not the same specification as gearbox fluid on most Land Rover and Range Rover units. The LT230 takes EP90 (or the Land Rover-specified MTF94 on later units), and the Magna Steyr unit on Discovery 3 and 4 takes a specific ATF spec. Confirm before ordering.
Most gearbox parts returns are caused by ordering errors at the buying stage rather than parts faults. The following are the most common we see across the Land Rover and Range Rover range.
For parts that overlap with the clutch system on manual gearboxes, see the Land Rover clutch parts collection. For driveline parts forward and aft of the gearbox, see the driveshaft and propshaft parts collection.
Technical GuidesIn-depth diagnostic and component guides for the gearbox-adjacent failure modes that come up most often on Land Rover and Range Rover models.
Technical breakdown of the L494's 3.0 TDV6 timing chain issues, air suspension faults, and ZF 8HP wear patterns. Covers what fails, why it fails, and which parts the workshop will need.
Range Rover Sport L494 ZF 8HP guideHow to tell drivetrain noise apart from gearbox or transfer box noise, and which parts to inspect before ordering. Covers Discovery 4, Freelander 2, and Series 3 driveline symptoms.
Land Rover driveline diagnosis guideClutch faults are routinely misdiagnosed as gearbox faults due to overlapping symptoms. This guide explains how to identify the real fault before replacing parts.
Land Rover clutch diagnosis guideThe gearbox controls gear ratios and torque delivery from the engine; the transfer box splits drive between the front and rear axles for 4x4 traction and also provides the low-range gearing on Defender and Discovery models. Both are serviceable assemblies and both fail in distinct ways. Drivetrain symptoms can come from either, which is why most Land Rover gearbox parts returns are caused by mis-diagnosis rather than mis-fit.
ZF 6HP26 transmissions (fitted to Range Rover L322, Range Rover Sport L320, Discovery 3, and Discovery 4) take ZF Lifeguard Fluid 6. ZF 8HP transmissions (fitted to Range Rover L405, L460, Range Rover Sport L494 and L461, and Discovery 5) take ZF Lifeguard Fluid 8. The two fluids are not interchangeable. Confirm the gearbox code stamped on the casing before ordering.
ZF's official position on the 8HP series is fill-for-life. In practice, independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km, particularly on vehicles used for towing, frequent urban driving, or high-mileage motorway work. The 6HP26 typically receives a service interval at 90,000 km. Manual gearboxes (R380, MT82, LT77) take a gear oil change at approximately 60,000 km.
The LT230, fitted to the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and Range Rover P38, fails in three main ways: output shaft seal leaks (often caused by flange wear behind the seal), input gear bearing wear, and selector linkage faults that mimic gearbox symptoms. Most LT230 issues are repairable with component-level parts rather than a full transfer case replacement.
The R380 five-speed manual was fitted to the Discovery 1 (post-200Tdi), Discovery 2, and Classic Defender from the 300Tdi era through to early Td5 production. The LT77 preceded the R380 on the Discovery 1 200Tdi. The MT82 six-speed replaced the R380 on the Defender 2.4 and 2.2 TDCi Puma. Rebuild kits and individual components for all three are stocked in this collection.
Yes. Most Land Rover transmission service jobs touch both units, particularly fluid changes, seal replacements, and bearing kits. Ordering both at the same time reduces vehicle downtime and is the most common workshop order pattern.