Land Rover Gearbox & Transferbox Parts

Bolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.

AUTOGEAR POWER SYN 75W-90 is based on high quality synthetic base oil in combination with a special additive package to ensure the following proper...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Transmission Oil Cooler Hose - Diesel Automatic is a hydraulic hose forming part of the automatic transmission cooling circuit on the Range Rover P...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Front Cover Gasket for the LT85 5-speed gearbox front cover joint. It seals the front cover against the gearbox case, retaining oil at the input e...

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Gear Lever Anti-Rattle Plunger Spring The lower plunger spring for the gear lever in the gearchange mechanism of the 5-speed manual gearbox (LT77 a...

Thrust Washer - 0.130" A gearbox mainshaft thrust washer for the second-speed gear, 0.130" thick. It controls the end-float of the 2nd-speed gear ...

2nd Speed Gear (29 teeth) for the mainshaft in the Series-type manual gearbox (LT76), from suffix D onwards. This gear meshes with its correspondi...

Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...

seal oil diff front Freel.1 Replacement 5 Speed-Manual-TD4 Diesel

Gear Lever Housing for the 5-speed manual gearchange assembly. It mounts on top of the gearbox and locates the gear lever, carrying the pivot and ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Gear Lever Bias Plate for the manual gearbox gear change mechanism. It sits in the gear lever remote housing and works with the bias spring to load...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Oil Cooler Pipe Auto - 300TDi ZF

Bolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Flywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Gearbox Sump Gasket for the automatic transmission oil pan. This is the gasket only - it seals the oil pan and oil screen to the gearbox case. For...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Spring Washer - 6mm for use across gearbox, clutch and general fastening applications. A helical split spring washer for M6 fasteners, providing r...

Layshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Reverse switch R380 Frl.1 manual

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Oil Temperature Switch - Gearbox Oil Cooler in the automatic transmission cooling circuit. This switch is mounted on the gearbox oil cooler and mo...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Transmission Output Shaft Grease for the MT82 six-speed manual gearbox. This specialist grease is applied to the gearbox output shaft splines, whe...

Gearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...

Retaining Plate - gearchange grommet retaining plate for the transfer box. Secures the transfer box gearchange grommet where the gear lever passes...

Washer Thrust 3rd Gear

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

Mudshield

Yoke Transmission

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...