Land Rover Interior Parts

Centre floor mounted storage cubby box providing an enclosed compartment between the front seats and additional cup holder provision within the int...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Gearbox Tunnel Insulation Pad - heat and sound insulation pad fitted to the gearbox tunnel around the gear lever. For manual transmission applicat...

Window Regulator Escutcheon - trim finisher that locates over the manual window winder spindle on the inner door, concealing the regulator aperture...

Door Checkstrap Cover for the front left-hand door, the trim cap that fits over the door check (checkstrap) mechanism. The checkstrap limits how f...

Door Card Fixing Kit for the interior door trim assembly of the Defender, in black. This kit provides the black-coloured rivets and fasteners requ...

Air Duct Seal - seals the heater air duct against the parcel tray within the HVAC air distribution. For vehicles without air conditioning.

Demister Outlet Finisher - vent finisher set into the top of the dashboard over the windscreen demister outlet, directing heated and ventilated air...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Pedal Pad is the moulded rubber cover that fits over a foot pedal within the pedal box assembly, providing a non-slip contact surface for the drive...

Clutch Pedal Torsion Spring is a return spring for the clutch pedal, fitted within the pedal box assembly on manual transmission vehicles. It prov...

Seat Back Foam is the moulded cushioning for the outer front seat back. It forms the padded profile that sits over the seat back frame, beneath the...

Floor Mat is a moulded rubber footwell mat shaped to fit the right-hand floor over the gearbox tunnel. The foam backing adds sound insulation unde...

Floor Mat is a moulded rubber footwell mat shaped to fit the left-hand floor over the gearbox tunnel. The foam backing adds sound insulation under...

Alloy Gear & Transfer Box Knobs Machined alloy replacement knobs for the main gear lever and the transfer box lever, supplied as a matching pai...

Instrument Panel Dash Mounting for the instrument binnacle assembly. This structural mounting bracket secures the instrument panel within the dash...

Facia Panel Assembly - LHD is the end closing trim for the upper dashboard fascia on left-hand drive Defender 90 and 110, finished in black. This ...

Gearbox Tunnel Cover in moulded rubber for the transmission tunnel. It fits over the tunnel around the gear and transfer levers, giving a finished ...

Leather hasp civilian

Cigar Lighter - the panel-mounted lighter and 12V accessory socket in the instrument panel electrical system. The assembly comprises a socket and ...

Seat Mounting Plates for the seat installation assembly, supplied as a pair. These plates provide the fixed interface between the seat base frame ...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Switch Panel provides the mounting location for auxiliary switchgear in the dashboard and parcel-tray area of the fascia. Manufactured from alumin...

Seat Belt Bracket provides the upper shoulder belt anchorage point in the front seat restraint system. Fitted to the left-hand side, it secures th...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Accelerator Pedal Pad - the moulded rubber cover that fits over the accelerator pedal. It provides a grippable, wear-resistant contact surface for...

Double DIN Console - one-piece centre console fascia in black, providing the mounting aperture for a double DIN head unit in the Td5 dashboard. It...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Waterproof Seat Cover Set - front seat covers finished in black, forming part of the vehicle's interior protection. The covers are made from water...

Cable Gaiter - Door Wiring is a protective sleeve and grommet fitted at the door aperture of the Defender body, routing the door wiring harness saf...

Heater grip OEM

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...

Seat Squab Hinge Link Rod - LH is part of the rear forward-facing split seat squab hinge assembly. The link rod connects the seat squab (backrest)...

Seat Linkage for the rear forward-facing split seat assembly. This right-hand link rod (squab hinge link) connects the seat squab hinge to the bac...

Seat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...

Seat belt bracket RH

Front Electric Window Kit converts the front door windows from manual wind-up to push-button electric operation. The kit provides the electric win...

Seat Re-trim Kit (Inner) re-covers the front centre seat, renewing the cushion and squab foams together with their outer covers to restore the seat...

Front Door Card is the interior trim panel that finishes the inner face of the front door, forming part of the interior door trim assembly. It fit...

grab handle for 3rd / 5th door (rear end door). Upto (VIN) 1A622423

Lower Steering Column Shroud is the lower half of the trim cover that encloses the steering column below the steering wheel. The moulded shroud co...

Seat Base - Techno Style The base cushion of a front seat, forming the seating surface that mounts to the seat frame and runners. Finished in the ...

Plastic Rivet is a push-fit fastener used to secure interior trim pads, finishers and insulation panels. It retains items such as radio and speake...

Front Floor Mat Pair covering the driver and front passenger footwells, supplied as a matched set of two. Shaped to the contour of the front floor...

Seat Box End Panel - Right-Hand is a repair panel forming the outer end face of the seat box assembly. It replaces the corroded offside end panel ...

Front Rubber Floor Mats for the driver and passenger footwells, supplied as a matched left- and right-hand pair. Moulded in rubber with a foam bac...