Land Rover Interior Parts

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Courtesy Light Switch is a door-actuated contact switch in the interior lighting circuit, mounted at the door pillar aperture. When the door is op...

Door Lock Button Escutcheon is the interior trim surround that frames the sill-mounted door lock button where it passes through the door casing. I...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

screw M5 x 12

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Fir Tree Clip push-in fastener used to secure interior door casings and trim panels to the body shell. The barbed fir-tree profile is pushed into ...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Size/Diameter: 1/4" unf x 7/8"

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Nylon Stud, a trim retaining fastener used to hold interior trim panels and carpet in position. The stud pushes into a pilot hole in the body pane...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Cap bolt

Sac Snap Clip

Trim Pad Clip is a fastening clip used to secure interior trim pads to the bodyside and door structure. It locates into a pre-formed hole in the p...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Drive Screw is a countersunk-head self-tapping screw used to secure body and interior trim components. The self-tapping thread cuts its own mating...

Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...

Electric Seat Switch for the right-hand seat cushion adjustment, part of the powered seat control assembly. Mounted in the seat base side trim, it...

Screw for body and interior trim fixing - a No.12 x 1/2" pan-head screw. Used to secure body panels, dash and facia, wheelarch and interior trim. ...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Steering Wheel Boss with a 36-spline fitting. Mounts onto the splined end of the steering column and provides the bolt pattern to which the steeri...

Gear Lever Gaiter, Inner. Flexible boot in the gear lever and transmission tunnel assembly. It seals the aperture where the main gearbox lever pas...

Windscreen Wash/Wipe Switch - steering column stalk switch controlling the front wiper and washer circuits. The switch mounts to the column switch...