Land Rover Series 1 Parts

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Wiper Blade for the front windscreen, with a stainless steel frame. The blade clears the driver's field of view across the front windscreen. It at...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Lock nut 3/8" BSF

Shock absorber bush (eye), anti roll bar bush

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Drive Flange Gasket

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Grommet

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

7" round LED headlamp 12/24V black 78W LHD (pair)

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Restore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Wind Deflector Set - a pair of stick-on air deflectors for the front door windows. Each deflector fits to the outer edge of the door window frame ...

Seat Base - Outer is the lower seat cushion for either outer (driver or passenger) position in the front seating assembly. Foam-padded and finishe...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...