Land Rover Series 1 Parts

Reverse Selector Fork for the gear selection mechanism in the Series-type manual gearbox (LT76), suffix B onwards. Mounted on the selector shaft, ...

Synchro Hub for the 3rd/4th gear synchroniser assembly in the Series-type manual gearbox (LT76). The hub carries the synchroniser mechanism that m...

Dipstick Tube - the guide tube through which the engine oil level dipstick passes down into the sump. It locates in the cylinder block and directs...

Roof Access Ladder in a hot-dip galvanised steel finish, providing safe access to a roof rack. This is a non-drill (bolt-on) type ladder that moun...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Gearbox Thrust Washer

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Steering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Bulkhead Top Corner Repair - LH

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)

The Jackall 48" Large Base Jack is the ultimate heavy-duty lifting solution for a variety of applications. With a massive 8,000lbs capacity, this j...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Metal Fuel Filler Cap seals the fuel tank filler neck, closing the fuel system against contamination, spillage and evaporative loss. The cap secur...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

Screw: pan head self-tapping screw.

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...