Land Rover Series 1 Parts

Joint Washer for the transfer gearbox top cover. This gasket seals the joint between the top cover and the transfer box housing, preventing oil le...

Speedo cable assy SII

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Sealing Ring

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Steering Relay Oil Seal for the steering relay unit, part of the steering linkage. The steering relay transfers movement from the steering box dro...

Front glazed door top assembly for the door upper structure. This component forms the upper section of the door frame and supports the glazed pan...

Blind Spot Mirror head for the left-hand door: a complete replacement mirror head with an integrated wide-angle convex section. The head measures ...

Spare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Wheel Cylinder Repair Kit for overhauling a front drum-brake wheel cylinder with a 1.25 inch bore. It restores the hydraulic seal of a worn or lea...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Wheel Nut for the road wheel and hub assembly, securing the road wheel onto the hub studs. The double-chamfer design is tapered at both ends, so t...

Spring plate

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Timing Chain for the 2.25L four-cylinder engine, part of the timing drive assembly. Drives the camshaft from the crankshaft sprocket, holding valv...

Fitment: All models to 1980 except V8

Joint Washer seals the gearchange/inspection cover against the transfer box casing within the transfer gearbox assembly. Fitted between the cover ...

Mainshaft Nut for the LT76 gearbox, fitted to the mainshaft and gear assembly. It retains the gear cluster on the mainshaft, clamping the stack ag...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Seat Back for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant leans agains...

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Gearbox Bearing is the ball bearing that supports the primary pinion, or first motion shaft, in the main gearbox. Located at the front of the gear...

Headlamp Bulb - 12V 40/45W Non-Halogen - LHD

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Layshaft Bearing for the Series manual gearbox. It supports the layshaft (countershaft) within the gearbox casing, allowing the constant-mesh gear ...

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Camshaft Sprocket for the engine timing drive assembly. Mounted on the nose of the camshaft and driven by the timing chain from the crankshaft spr...

LED Lamp Upgrade Kit: 73mm LED lamp units that replace the original bulb-type lamp units.

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Track Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Swivel Housing Gaiter Kit in leather for the front axle swivel housings, supplied as an axle set to cover both sides. The gaiter encloses the swiv...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Inlet Valve - the poppet valve that seals the inlet port in the cylinder head and opens on the induction stroke to admit the incoming air charge to...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...