Land Rover Series 1 Parts

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Turnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Shock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...

Rotor Arm for the Lucas distributor in the ignition system of the 2.0L and 2.25L 4-cylinder petrol engines (up to engine suffix C). Driven by the ...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Exhaust Valve - the poppet valve that seals the exhaust port in the cylinder head and opens on the exhaust stroke to release spent combustion gases...

Accelerator Rod Ball Joint forms an articulated pivot in the accelerator (throttle) control linkage, joining adjacent sections of the accelerator r...

Hot Plug - 2.0L & 2.25L Diesel

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Valve Stem Seal for the IOE (inlet-over-exhaust) engine valvetrain. Fitted over the valve stem at the top of the valve guide, it closes the cleara...

Headlamp Surround — the chrome bezel that trims and retains the outer edge of a 7-inch round headlamp. A polished chrome ring fitted over the head...

Parabolic Spring and Shock Kit - a front leaf-spring suspension package for short- and long-wheelbase applications. The two-leaf parabolic springs...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Starter Switch for Land Rover Series 1 and Series 2 models (1948-1966). This switch activates the starter solenoid to engage the starter motor whe...

In/out member

Front Door Seal Kit for the left-hand front door, supplied with the rivets required for fitting. The kit contains the door sealing rubbers to re-s...

Front Door Seal Kit re-seals the right-hand front door aperture, supplied with the rivets needed to fit it. The kit contains six door sealing rubb...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Shim plate

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Leather hasp civilian

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

4-Leaf Parabolic Rear Spring Pair for the rear suspension of Series long-wheelbase Land Rovers. Parabolic leaf springs use a progressive, variable...

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Fixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. The plate is a fixed, non-adjustable type set...

Window Channel - Vertical - the upright glass run for the Truck Cab side window, part of the door glazing assembly. It lines the vertical edge of ...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...