Land Rover Series 1 Parts

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Exhaust Pipe - Intermediate - Non-Station Wagon

Ball Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...

Gearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Gearbox Stud is a 1 3/4" threaded stud used in the gearbox and transfer box assembly. It provides a fixed threaded anchor for clamping casing join...

Brake Kit - Series - SWB - To June 1980

Bulkhead Top Corner Repair - LH

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Water Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...

7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)

motor wiper single replacement (NLA wanneer op!)

Layshaft for the Series Land Rover gearbox. The layshaft (countershaft) runs parallel to the mainshaft inside the gearbox casing. It is driven con...

Polyurethane chassis- and spring bushes as well as shock absorber bushes for all Series Short Wheelbase and Series 1 and 2/2A LWB. (For S3 LWB use ...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Clutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...

Threaded Core Plug seals a threaded aperture in the engine block casting, used on the 4-cylinder petrol engine as a blanking plug for a redundant h...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Folding Side Step - Series

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Metal Fuel Filler Cap seals the fuel tank filler neck, closing the fuel system against contamination, spillage and evaporative loss. The cap secur...

Transfer Box Sump Cover is a finned billet aluminium cover plate that replaces the pressed-steel sump cover on the underside of the transfer case. ...

Upgrade your Land Rover's steering system with Heavy-Duty Steering Arms, designed for superior strength and performance, especially in off-road con...

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

Footwell Repair Panel for the right-hand (offside) footwell - a body repair section covering the footwell floor and inner side panel. For right-han...

Doortop Unglazed - LH

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...

Layshaft Split Ring Halves are a matched pair of semi-circular retaining ring halves used in the Land Rover Series I and II gearbox assembly. The ...

Rear Shackle Pin for the rear leaf spring shackle. The pin secures the spring shackle at the rear mounting of the rear leaf spring, allowing the s...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Replacement brake pads for handbrake conversion kit - DA5537