Land Rover Series 1 Parts

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

In/out member spring

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Plain Washer M8

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Headlamp Bowl Kit - Series

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Fuel Pipe Sealing Washer seals the fuel pipe union at the DPA diesel injection pump. Fitted at the union connection, it is compressed between the ...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Gearbox Thrust Washer

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Bronze Distance Piece Mainshaft 1954-71

Swivel Pin

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Free Wheeling Hub Kit - manual locking front-axle hubs that connect or disconnect the front halfshafts from the road wheels. Set to free, the front...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Switch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...

Tailgate Chain Bracket

Shock Absorbers for the rear axle, supplied as a matched pair. Each damper controls suspension movement by converting the energy of spring oscillat...

Pop Rivet (blind rivet) used to secure the flexible door rubber, a body and door-trim fixing. The rivet fastens the flexible rubber seal to the do...

Autolite Work Lamp - Square - 55W

Strap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Universal Joint for the propeller shaft, measuring 82 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Electric Fuel Pump - an SU-type electric fuel pump in the low-pressure fuel delivery circuit. It draws petrol from the tank and delivers it to the...