Land Rover Series 2 & 3 Parts

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Brake Pipe Union - a female threaded union nut for the brake hydraulic pipework, with a 7/16"-20 UNF thread sized for 1/4" brake pipe. It fastens ...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Anti-Burst Door Lock for the left-hand front door, the latch mechanism that secures the door to the body. The latch engages the striker on the doo...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Sealing O-Ring for the joint between the flywheel housing and the engine block on the 2.25L 5-bearing petrol and 2.5L naturally-aspirated diesel en...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

LED Lamp Upgrade Kit: 73mm LED lamp units that replace the original bulb-type lamp units.

Brush set M418G

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Radiator Panel Screw is a fixing screw for the radiator and fan cowl assembly. It secures the radiator panel and fan cowl to their mounting, holdi...

Clevis Pin - a linkage pin used in the accelerator and throttle control. It joins the throttle cable clevis to its operating lever, allowing the l...

Transfer Box Intermediate Shaft Shim, 0.005in thick, used in the transfer box to set the end float of the intermediate gear on its shaft. Selectiv...

Timing Chain Locking Plate for the timing chain drive of the 2.25L and 2.5L 4-cylinder petrol engine. The plate locks the camshaft sprocket retain...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Nyloc Nut with a 1/2" BSF thread. A nylon insert in the crown of the nut grips the bolt thread as it is tightened, resisting loosening under vibra...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

Bulb - 24V 21W A 24-volt, 21-watt incandescent bulb for the exterior lighting and signalling circuits. Rated for 24V electrical systems, it is a s...

Distributor - contact-breaker (points) ignition distributor for the 4-cylinder petrol engine. Distributes the high-tension spark to the cylinders ...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Ignition Switch is the key-operated electrical switch mounted on the steering column, at the heart of the ignition and starting circuit. It selects...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Timing Chain Vibration Damper for the front timing chain drive on four- and six-cylinder engines. Mounted within the timing cover, it bears agains...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Inlet Valve - the poppet valve that seals the inlet port in the cylinder head and opens on the induction stroke to admit the incoming air charge to...

Collapsible Salisbury spacer

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

hinge front door RH upper with holes for mirror arm "smaller" version for Series 3 and early classic Defender upto (VIN) WA138479 (1998 model year)

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Upper Rear Door Hinge, aluminium, for the rear end (tailgate) door, part of the body and door assembly. It is the upper of the two hinges that car...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Window Channel